CHAPTER Using Your Hub Software 3-13Using Your Hub SoftwareThis chapter describes procedures for configuring the Cisco Micro Hub, and contains the fol
Configuring the HubCisco Micro Hub User Guide3-10Step 3 Use the ip trap-manager command to configure the IP address of the SNMP management station:Hub
Using Your Hub Software 3-11Command SummaryCommand SummaryThis section provides a summary of the commands used to configure the Micro Hub 1503. The c
Command SummaryCisco Micro Hub User Guide3-12Commands are defined and described in the format shown below:show hub informationSyntax: show hub infor
Using Your Hub Software 3-13System Help CommandsSystem Help CommandsUse the commands in this section to obtain system help when configuring the hub.h
Command SummaryCisco Micro Hub User Guide3-14User Interface CommandsUse the commands in this section to configure the user interface for the hub softw
Using Your Hub Software 3-15User Interface CommandsexithelpConsole Access CommandsUse the commands in this section to control console access to the h
Command SummaryCisco Micro Hub User Guide3-16console-lockoutno console lockoutconsole-lockout timeSyntax: console-lockoutMode: AdministratorDescriptio
Using Your Hub Software 3-17User Interface CommandsAdministrator Password CommandsUse the commands in this section to configure hub passwords.passwor
Command SummaryCisco Micro Hub User Guide3-18telnet-session passwordno telnet-session passwordtelnet-sessionSyntax: telnet-session passwordMode: Admin
Using Your Hub Software 3-19User Interface CommandsHistory CommandsUse these commands in this section to configure how the hub stores and displays co
Preparing for ConfigurationCisco Micro Hub User Guide3-2Connection Using TelnetIf the hub is correctly connected to a network, you can access the hub
Command SummaryCisco Micro Hub User Guide3-20terminal history sizeEditing CommandsUse the commands in this section to configure the hub for terminal e
Using Your Hub Software 3-21Firmware Load and Restart CommandsFirmware Load and Restart CommandsUse the commands in this section to configure how the
Command SummaryCisco Micro Hub User Guide3-22TFTP Download CommandsUse the commands in this section to configure how the hub downloads firmware from a
Using Your Hub Software 3-23Firmware Load and Restart Commandsstart tftp-downloadXmodem Download CommandUse this command to download firmware to the
Command SummaryCisco Micro Hub User Guide3-24Restart CommandUse this command to reset the hub.restartSyntax: restartMode: AdministratorDescription: Pe
Using Your Hub Software 3-25System Information CommandsSystem Information CommandsUse the commands in this section to display general information abo
Command SummaryCisco Micro Hub User Guide3-26system nameno system namesystem contactSyntax: system name <string>Mode: AdministratorDescription:
Using Your Hub Software 3-27System Information Commandsno system contactsystem locationno system locationSyntax: no system contactMode: Administrator
Command SummaryCisco Micro Hub User Guide3-28show management informationSyntax: show management information Mode: GuestDescription: Displays informati
Using Your Hub Software 3-29Management Configuration CommandsManagement Configuration CommandsUse the commands in this section to configure community
Using Your Hub Software 3-3Command ConventionsCommand ConventionsThis section describes some things you might need to know before using the commands
Command SummaryCisco Micro Hub User Guide3-30ip addressno ip addressSyntax: ip address {ip-address} [subnet mask] [gateway ip]Mode: AdministratorDescr
Using Your Hub Software 3-31Management Configuration CommandsSNMP Communities CommandsUse the commands in this section to configure the SNMP communit
Command SummaryCisco Micro Hub User Guide3-32snmp communitysnmp community disableSyntax: snmp community {index} {string} [ro | rw]Mode: AdministratorD
Using Your Hub Software 3-33Management Configuration Commandssnmp community enablesnmp trap-authenticationno snmp trap-authenticationSyntax: snmp com
Command SummaryCisco Micro Hub User Guide3-34Configuring Trap ManagersUse the commands in this section to configure the Micro Hub 1503 trap informatio
Using Your Hub Software 3-35Management Configuration Commandsip trap-managerip trap-manager enableip trap-manager disableSyntax: ip trap-manager {ind
Command SummaryCisco Micro Hub User Guide3-36Hub Configuration CommandUse the commands in this section to display information about hubs in a stack.sh
Using Your Hub Software 3-37Port Configuration CommandsPort Configuration CommandsUse the commands in this section to display or edit information abo
Command SummaryCisco Micro Hub User Guide3-38port operationSyntax: port-operation {hub id} {port id} {enable | disable}Mode: AdministratorDescription:
Using Your Hub Software 3-39Statistics CommandsStatistics CommandsUse the commands in this section to display statistics for a stack, a specific hub
Preparing for ConfigurationCisco Micro Hub User Guide3-4• You can abbreviate commands to the fewest letters that make them unique. For example, for th
Command SummaryCisco Micro Hub User Guide3-40show hub statisticsSyntax: show hub statistics [hub id]Mode: GuestDescription: Displays statistics for th
Using Your Hub Software 3-41Statistics Commandsshow port statisticsSyntax: show port statistics {hub id} {port id}Mode: GuestDescription: Displays st
Command SummaryCisco Micro Hub User Guide3-42• Frames too long—Number of times that the frame length has exceeded the maximum allowable size (1518 byt
Using Your Hub Software 3-43Statistics Commandsclear counters Syntax: clear counters {stack | hub [hub id]|port [hub id] [port id]}Mode: Administrato
Command SummaryCisco Micro Hub User Guide3-44Chassis Information CommandsUse the commands in this section to display chassis information for the Cisco
Using Your Hub Software 3-45Chassis Information Commandsshow card tableSyntax: show card tableMode: GuestDescription: Displays information about the
Command SummaryCisco Micro Hub User Guide3-46show stack informationstack nameSyntax: show stack informationMode: GuestDescription: Displays a descript
Using Your Hub Software 3-47Chassis Information Commandsstack ip addressclear stack tableSyntax: stack ip address {ip address}Mode: AdministratorDesc
Command SummaryCisco Micro Hub User Guide3-48
Using Your Hub Software 3-5Forgot Your Password?The <password> field can contain from 0 to 80 uppercase and lowercase alphanumeric characters.
Configuring the HubCisco Micro Hub User Guide3-6Step 7 The following message appears, confirming that your new passwords have been accepted:Administra
Using Your Hub Software 3-7Hub ID NumbersHere are two rules that determine hub ID numbers in a stack of hubs:1 The lowest hub ID number in a stack (1
Configuring the HubCisco Micro Hub User Guide3-8Configuring the hub takes place in three major steps:1 Entering Administrator Mode2 Configuring IP and
Using Your Hub Software 3-9Configuring IP and SNMP ParametersConfiguring IP and SNMP ParametersThe illustration below shows the network that is being
Comments to this Manuals