Cisco 3600 - 24 Port Digital Modem Network Module Installation Guide Page 57
- Page / 142
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Connecting Serial Network Modules to a Network 6-5
Asynchronous Network Modules Interface Numbering
Ports are numbered from right to left and from bottom to top, as labeled on the module’s
rear panel. (See the “Asynchronous Network Modules Interface Numbering” section on
page 6-5.)
Octal cables are not provided with the network module. For ordering information, see the
“Cisco Connection Online” section on page xiv.
Use an octal cable, and adapters if necessary, to connect each of the modules’s 68-pin
receptacles to one or more asynchronous modems, terminals, or other devices. (See
Figure 6-1.)
Figure 6-1 Connecting an Asynchronous Network Module to an Asynchronous
Device
Asynchronous Network Modules Interface Numbering
Certain Cisco IOS configuration commands identify asynchronous ports by an interface
number (or a line number, which is the same as the interface number). The interface number
of a port on a asynchronous network module is related to the slot number where the module
is installed and the unit number of the port in the module.
EN
ASYNC
ASYNC 8-15
ASYNC 0-7
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
ASYNC 24-31
ASYNC 16-23
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
H9999
RJ-45 to DB-25 adapter
Modem or terminal
- About This Guide 1
- Audience 2
- Organization 2
- Conventions 4
- Cisco Connection Online 6
- Ordering Documentation 7
- Overview of Cisco Network 9
- Slot Numbering 12
- DO NOT INSTALL WAN INTERFACE 13
- CARDS WITH POWER APPLIED 13
- Unit Numbering 14
- Cisco 2600 Series Routers 15
- Slot and Unit Numbering 17
- Preparing to Install Network 19
- Safety Warnings 20
- Required Tools and Equipment 22
- Installing Network Modules in 23
- Cisco Modular Routers 23
- Asynchronous network module 24
- Blank Network Module Panels 25
- WAN interface card 27
- Connecting Ethernet Network 31
- Connecting Ethernet Ports 32
- AUI Connections 33
- 10BaseT Connections 33
- Ethernet 10BaseT 34
- 10BaseT hub 34
- 10BaseT cable 34
- 1-Port Fast Ethernet Module 35
- 10/100 bTX 37
- FAST ETHERNET 37
- LEDs Enable 37
- Connecting Fast Ethernet PRI 39
- 10/100BaseT 40
- Connecting the PRI Ports 42
- CT1/PRI port (DB-15) 43
- CTRLR 1CTRLR 0 44
- CT1/PRI CSU 45
- • CE1/PRI-B Port on page 5-9 47
- • CE1/PRI-U Port on page 5-11 47
- Connectors) 48
- CE1/PRI-U Port 49
- Fast Ethernet PRI Module LEDs 50
- Connecting Serial Network 53
- Serial DTE or DCE Devices 54
- Signaling Standards Supported 54
- Distance Limitations 55
- Asynchronous Devices 56
- RJ-45 to DB-25 adapter 57
- Modem or terminal 57
- Slot 0Slot 1 Power supply 58
- 1 Cisco 3640 router only 59
- 4-Port Serial Network Module 62
- • V.35 Serial Cable Assembly 63
- • X.21 Serial Cable Assembly 63
- Serial port LEDs 65
- ASYNC 24-31 ASYNC 16-23 66
- ASYNC 8-15 66
- ASYNC 0-7 66
- Network Module 67
- LEDs shown in Table 6-7 70
- Connecting ISDN BRI Network 71
- BRI 3 BRI 2 BRI 1 BRI 0 73
- B1 B2 B1 B2 B1 B2 B1 B2 73
- BRI S/T Module LEDs 74
- BRI U ports (RJ-45) 76
- NT1 LEDs 77
- ISDN BRI LEDs 77
- BRI U Modules LEDs 78
- Connecting ISDN PRI Network 81
- CT1/PRI-U port (DB-15) 82
- CT1/PRI-U ports (DB-15) 83
- CT1/PRI Module LEDs 84
- Network Modules 85
- CT1/PRI CSU Module LEDs 87
- Table 8-2 88
- (120-ohm) Network Modules 89
- (DB-15-to-DB-15 Connectors) 91
- 1FE-1CE1-B/U 92
- CE1/PRI Module LEDs 93
- (75-ohm) Network Modules 94
- CSU with BNC connectors 95
- Connecting Voice Network 99
- Voice Network Module LEDs 101
- Connecting Digital 103
- Modem Network Modules to a 103
- Hardware Requirements 105
- Interface Numbering 106
- Figure 10-3.) 108
- Alignment holes 109
- Connector edge 109
- Removing 6-Port MICA Modules 111
- Digital Modem Module LEDs 118
- Connecting Analog Modem 119
- Network Modules to a Network 119
- 76543210 120
- 15 14 13 12 11 10 9 8 120
- Supported Network Protocols 121
- RJ-11 jack 124
- Analog modem port (RJ-11) 124
- Straight-through 124
- RJ-11 cable 124
- 76543210IN USE 125
- 15 14 13 12 11 10 9 8 IN USE 125
- Connecting ATM Network 127
- Modules to a Network 127
- RJ-45 port 128
- Enable LED 128
- ATM traffic 128
- ADSL modem 129
- RJ-45-to-RJ-45 cable 129
- ATM-25 port 129
- ATM-25 Network Module LEDs 130
- Connecting HSSI Network 131
- HSSI port LEDs 132
- HSSI port 132
- External DSU 133
- HSSI DTE cable 133
- HIGH SPEED SERIAL 133
- HSSI Network Module LEDs 134
- Connecting Compression 137
- Supported Interfaces 138
- COMPRESSION 139
- Error LED 139
- Active LED 139
- FCC Class B Compliance 141
Related products and manuals for Networking Cisco 3600 - 24 Port Digital Modem Network Module
Networking Cisco CISCO7201 User Manual
(28 pages)
(28 pages)
(44 pages)
Networking Cisco 1900 series Specifications
(44 pages)
(44 pages)
Networking Cisco DPC2202 User Manual
(8 pages)
(8 pages)
Networking Cisco EPC3208 User Manual
(98 pages)
(98 pages)
Networking Cisco CX-TRIP2 Specifications
(28 pages)
(28 pages)
Networking Cisco SRW248G4P User Manual
(5 pages)
(5 pages)
(48 pages)
Networking Cisco 3631 Specifications
(198 pages)
(198 pages)
Networking Cisco SRW224 User Manual
(5 pages)
(5 pages)
© 2020, manymanuals.com. All rights reserved. | 0.197 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals