Cisco MC3810-V - Concentrator - External Installation Guide

OBTAIN TOOLS AND EQUIPMENTINSTALL CHASSIS AND CONNECT CABLESGET SITE INFORMATIONPOWER UP THE CISCO MC3810PERFORM INITIAL CONFIGURATION12345Telephonene

8Install Chassis and Connect Cables (continued)Ethernet hubCisco MC3810187Straight-throughEthernet cable10BaseT port(RJ-45)235614E&MFXOE&ME&am

9Install Chassis and Connect Cables (continued)TelephonePBXFXS port FXO portE&M portCisco MC3810235614RJ-11 jackto central officeT1/E1ConnectingAn

10Install Chassis and Connect Cables (continued)Digital voice port(RJ-48 shown)Cisco MC3810PBXRJ-48-to-RJ-48 rollover cableor two 75-ohm coaxialcables

11Install Chassis and Connect Cables (continued)BRI voice ports(CB-1D)Cisco MC38108-conductor cablesB2B1ALMB2B1ALMALMB2B1ALMB2B1BRI 1BVMBRI 2BRI 3BRI

12Install Chassis and Connect Cables (continued)Cisco MC3810Video codecDialing port Video data portSerial port0 or 1VDM portRS-366 cableV.35 DCEwith R

13Install Chassis and Connect Cables (continued)Console port(RJ-45)RJ-45-to-RJ-45 rollover cablePC (laptop)RJ-45-to-DB-9 orRJ-45-to-DB-25 adapter(labe

14Install Chassis and Connect Cables (continued)Cisco MC3810RJ-45-to-RJ-45 rollover cableModemRJ-45-to-DB-25 adapter(labeled MODEM)235614Auxiliary (AU

15Install Chassis and Connect Cables (continued)To poweroutletCisco MC381023561T1/E14E&MFXOE&ME&ME&ME&MPowerswitchConnecting the P

16Get Site InformationGet This Information from Your Network AdministratorThis table provides space to write down information you need to run the Syst

17Power Up the Cisco MC3810Checklist for Power-UpYou are ready to power up the Cisco MC3810 if it meets these requirements:• Securely mounted• Power c

18Perform Initial ConfigurationThis section shows how to perform some basic configurations from a local or remote console, using the Ciscocommand-line i

19Perform Initial Configuration (continued)NowthattheEthernetporthasanIPaddress,youcaneitherconfiguretheCiscoMC3810remotelywithaTelnetconnection, or you

20Perform Initial Configuration (continued)Configuring Basic Settings for Serial Ports 0 and 1To configure basic settings for serial ports 0 and 1, do th

21Perform Initial Configuration (continued)Configuring T1/E1 Controller Settings for T1/E1 PortsThere can be two T1/E1 ports in a Cisco MC3810: a trunk

22Perform Initial Configuration (continued)Configuring T1 Controller SettingsTo configure T1 controller settings, do the following in controller configura

23Perform Initial Configuration (continued)Basic Voice-Port ConfigurationThis section has separate procedures for analog, digital, and ISDN BRI voice po

24Perform Initial Configuration (continued)Configuring Analog Voice PortsTo configure the basic analog voice-port settings, perform the following tasks:S

25Perform Initial Configuration (continued)Note: If you are not going to use a voice port, shut it down to conserve bandwidth.To configure voice-port tu

26Perform Initial Configuration (continued)Note: If you are not going to use a voice port, shut it down to conserve bandwidth.To configure voice-port tu

27Perform Initial Configuration (continued)Verifying Your Analog or Digital Voice-Port ConfigurationYou can test your analog or digital voice-port config

1Obtain Tools and EquipmentItems Included• Cisco MC3810 multiservice access concentrator• Rack-mountbrackets,powercord, and spare setof rubber feet• R

28Perform Initial Configuration (continued)Configuring ISDN BRI Voice PortsTo configure the basic ISDN BRI voice-port settings, perform the following tas

29Perform Initial Configuration (continued)Step Command Purpose9router(config-interface bri 1)#isdn overlap-receivingActivate overlap signaling to the

Corporate HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706USAhttp://www.cisco.comTel: 408 526-4000800 553-NETS (6387)Fax: 4

2Install Chassis and Connect CablesFront panel forwardRear panel forward23561T1/E14E&ME&ME&ME&ME&MFXORear panel forward,center-mou

3Install Chassis and Connect Cables (continued)Vertical wall studPower supply and fan at the topWall-Mounting the ChassisStep 1 Install the smaller br

4Install Chassis and Connect Cables (continued)Identifying Cable Types8-Conductor Rollover CableHold the connectors side-by-side, with the tab at theb

5Install Chassis and Connect Cables (continued)Cisco MC38105FXOFXO235614E&MFXOE&ME&ME&ME&MT1/E1 trunk port(RJ-48 shown)RJ-48 strai

6Install Chassis and Connect Cables (continued)Cisco MC3810235614ISDN wall jack(U interface)BRI S/T backup port(CB-1D)8-conductorstraight-through cabl

7Install Chassis and Connect Cables (continued)Cisco MC3810CSU/DSUSerial 1portSerial 0portCisco serialtransitioncablesFXO235614E&MFXOE&ME&