Cisco 3040 Installation Guide

Getting Started GuideCisco Catalyst Blade Switch 3040 for FSC Getting Started GuideINCLUDING LICENSE AND WARRANTY1 Introduction2 Taking Out What You

10 Step 6 Ensure that the release latch on the blade switch is in the open position. (See Figure 4.)Figure 4 Open the Blade Switch Release LatchStep 7

11 Figure 5 shows the blade switch being inserted into the BX600 system.Figure 5 Inserting the Blade Switch into the BX600 System Step 9 If you are se

12 Connecting through the Blade Switch Console PortFollow these steps to set up the blade switch by connecting it to a PC through its console port:Ste

13 Step 2 Start the terminal emulation session so you can see the output display from the power-on self-test (POST).Step 3 On the PC terminal emulatio

14 Figure 7 Connecting through the BX600 System Management BladeStep 2 On the PC terminal emulation program:a. Set the data format to 8 data bits, 1 s

15 Step 3 On the console monitor, the management blade application displays a login screen. Log in by using these defaults: username root password roo

16 Step 10 Go to “Waiting for POST to Complete” section on page 16 to finish configuring the blade switch.If the blade switch is already installed and

17 Completing the Initial ConfigurationFollow these steps to complete the setup program and to create an initial configuration.Note For information ab

18 Step 6 (Optional) Configure Simple Network Management Protocol (SNMP) by responding to the prompts. To configure SNMP later, press Return (which ap

19 no shutdownip address 10.0.0.1 255.255.255.0!interface GigabitEthernet0/1!interface GigabitEthernet0/2. . . (output truncated)interface GigabitEthe

2 1 IntroductionThis guide provides instructions on how to install your Cisco Catalyst Blade Switch 3040 for FSC—referred to as the blade switch—in t

20 5 Managing the Blade SwitchAfter you complete the initial configuration, use the device manager or other management options described in this sect

21 Step 3 Use the device manager to perform basic blade switch configuration and monitoring. Refer to the device manager online help for more informat

22 • To reset the IP address, the subnet mask, or the gateway address, enter the new settings in the appropriate field, and click Apply and Reload. Th

23 Other Management OptionsYou can use SNMP management applications to configure and to manage the blade switch. You also can manage it from an SNMP-c

24 Resetting the Switch ConfigurationThis section describes how to reset the blade switch configuration by rerunning the system configuration dialog.

25 • Network interface cards• Troubleshooting tools• Field notices and security advisoriesFollow these steps:1. Open your browser, and go to http://ww

26 7 Obtaining DocumentationCisco documentation and additional literature are available on Cisco.com. Cisco also provides several ways to obtain tech

27 Nonregistered Cisco.com users can order technical documentation from 8:00 a.m. to 5:00 p.m. (0800 to 1700) PDT by calling 1 866 463-3487 in the Uni

28 Reporting Security Problems in Cisco ProductsCisco is committed to delivering secure products. We test our products internally before we release th

29 Cisco Technical Support & Documentation WebsiteThe Cisco Technical Support & Documentation website provides online documents and tools for

3 Cisco Gigabit Ethernet Blade Switch DescriptionFigure 1 shows the blade switch, which has these features:• 10 internal Gigabit Ethernet 1000BASE-X p

30 To open a service request by telephone, use one of the following numbers:Asia-Pacific: +61 2 8446 7411 (Australia: 1 800 805 227)EMEA: +32 2 704 55

31 • Cisco Press publishes a wide range of general networking, training and certification titles. Both new and experienced users will benefit from the

32 12 Hardware Warranty TermsThis section describes the warranty terms for the blade switch.FSC Hardware Warranty TermsNote Important Note about Your

33 d. Read the document online, or click the PDF icon to download and print the document in Adobe Portable Document Format (PDF).Note You must have Ad

34 To Receive a Return Materials Authorization (RMA) NumberContact the company from whom you purchased the product. If you purchased the product direc

35 3040GSG.fm Page 35 Monday, September 18, 2006 9:45 AM

Corporate HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706USAwww.cisco.comTel: 408 526-4000800 553-NETS (6387)Fax: 408 526-

Information on this document On April 1, 2009, Fujitsu became the sole owner of Fujitsu Siemens Compu-ters. This new subsidiary of Fujitsu has been re

4 The blade switch is powered from the BX600 S2 system backplane, and temperature management is provided by the BX600 S2 system. The blade switch has

5 3 BX600 System ArchitectureThe four BX600 system I/O blade slots are on the rear panel (see Figure 2). You can insert blade switches into the NET1,

6 Figure 3 shows the BX600 system management blade on the left and an optional advanced KVM blade on the right.Figure 3 BX600 System Management and Ad

7 Table 1 describes the BX600 system management blade LEDs:Note For more information about the master and failure management blade LEDs or the advance

8 4 Preparing to Install the Blade Switch in the BX600 SystemBefore you install the blade switch in the BX600 system, review the safety and complianc

9 Installing the Blade Switch in the BX600 SystemFollow these steps to install the blade switch in the BX600 system:Step 1 Obtain and make note of thi