Cisco WS-C2924M-XL-EN-5P Datasheet Page 5

  • Download
  • Add to my manuals
  • Print
  • Page
    / 6
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 4
Cisco Systems
Copyright © 2001 Cisco Systems, Inc. All Rights Reserved.
Page 5 of 6
Secures a port to an individual MAC address group of
up to 132 MAC addresses; addresses can be learned or
manually entered; can prevent unauthorized stations
from accessing the switch.
Password-protected in-band and out-of-band
management provides protection against unauthorized
configuration changes and secures against unwanted
intruders. Provides administrators the choice of level of
security, notification, and resulting actions.
TACACS+authentication enablescentralized control of
theswitchandrestrictsunauthorizedusersfromaltering
the configuration.
Private VLAN Edge provides security and isolation
between ports on a switch, ensuring that voice traffic
travels directly from its entry point to the aggregation
device through a virtual path and cannot be directed to
a different port.
Support for the optional Cisco 600-watt redundant
AC power system provides a backup power source
for up to four units for improved fault tolerance and
network uptime.
Multilevel security on the console access prevents
unauthorized users from altering the switch
configuration.
Cisco Uplink Fast technology ensures quick failover
recovery, enhancing overall network stability and
reliability.
Cross-stack Uplink Fast (CSUF) technology provides
increased redundancy and network resiliency through
fast spanning-tree convergance (less than 2 seconds)
across a stack of switches using Gigastack GBICs.
Redundant stacking connections support a redundant
loopback connection in top and bottom switches in
a stack.
Command Switch Redundancy allows customers to
designate a backup command switch, which takes over
clustermanagement functionsin theeventof afailure of
the primary command switch.
Unidirectional Link Detection (UDLD) detects and
disables unidirectional links caused by incorrect wiring
or interface faults, preventing Spanning Tree loops.
Technical Specifications
Performance
3.2 Gbps switching fabric
3.0 million-pps forwarding rate for 64-byte packets
1.6 Gbps maximum forwarding bandwidth
4-MB shared-memory architecture shared by all ports
Packet forwarding rate for 64-byte packets:
14,880 pps to 10-Mbps ports
148,800 pps to 100BaseT ports
8-MB DRAM and 4-MB Flash memory
8192 MAC addresses
Management
SNMP Management Information Base (MIB) II, SNMP
MIB extensions, Bridging MIB (RFC 1493)
Standards
IEEE 802.3x full duplex on 10Base-T and
100Base-T ports
IEEE 802.1D Spanning-Tree Protocol
IEEE802.3u100Base-TXand100Base-FXspecification
IEEE 802.3 10Base-T specification
IEEE 802.3z
IEEE 802.3ab
Connectors and Cabling
10Base-Tports:RJ-45connectors;two-pairCategory3,
4, or 5 unshielded twisted-pair (UTP) cabling
100Base-TX ports: RJ-45 connectors; two-pair
Category 5 UTP cabling
Management console port: RJ-45 connector
Indicators
Per-port status LEDs—link integrity, disabled, activity,
speed, and full-duplex indications
System status LEDs—system, RPS, module status, and
bandwidth utilization indications
Dimensions and Weight (H x W x D)
3.46 x 17.5 x 12 in. (8.8 x 44.5 x 30.5 cm)
13.5 lb (6.12 kg)
15 lb (6.8 kg) with two modules installed
Page view 4
1 2 3 4 5 6

Comments to this Manuals

No comments