Cisco IAD2431-1T1E1 Installation Guide

Quick Start GuideCisco IAD2430 Series Integrated Access DevicesINCLUDING LICENSE AND WARRANTY1 Cisco 90-Day Limited Hardware Warranty Terms2 Related D

10Rack-Mounting the ChassisThe following warning applies only when the unit is rack-mounted:WarningTo prevent bodily injury when mounting or servicing

11Figure 7 Telco 19-Inch Rack-Mounting with Rear Panel ForwardStep 2 Install the chassis in the rack.Wall-Mounting the ChassisThe following warning ap

12• Attach both brackets to the wall.Note For attaching to a wall stud, each bracket requires two #10 wood screws (round- or pan-head) with #10 washer

13Grounding the ChassisWarningThis equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence ofa suitably

14Step 4 Attach the ground lug or ring terminal to the chassis as shown in Figure 10 or Figure 11. For the ground lug, use thetwo screws with captive

15Note Contact your Cisco account representative for the most recent supported cards.For detailed information on installing and connecting interface c

16WarningBefore performing any of the following procedures, ensure that power is removed from the DC circuit. Statement1003WarningTo prevent accidenta

17Figure 12 LAN, Administrative Access, and Power ConnectionsConnecting WAN and Voice CablesWarningFor connections outside the building where the equi

18Figure 13 WAN and Voice Connections8 Powering On the Cisco IADCaution Do not use AC and DC power at the same time. If you do, the unit stops operati

19To power on the Cisco IAD, follow this procedure:Step 1 Power on your terminal or PC, and configure it for 9600 bps, 8 data bits, 1 stop bit, and no

21 Cisco 90-Day Limited Hardware Warranty TermsThere are special terms applicable to your hardware warranty and various services that you can use duri

20Setting the Fast Ethernet Port IP AddressTo set an IP address for the Fast Ethernet port, follow the procedure below. After setting this address, yo

21Configuring Digital VoiceTo configure basic T1/E1 controller settings to support Point-to-Point Protocol (PPP), High-Level Data Link Control (HDLC),

22Verifying and Saving Your ConfigurationTo verify the configuration and save it in NVRAM so that the configuration remains in effect if the Cisco IAD

2310 Obtaining DocumentationCisco documentation and additional literature are available on Cisco.com. Cisco also provides several ways to obtain techn

2412 Cisco Product Security OverviewCisco provides a free online Security Vulnerability Policy portal at this URL:http://www.cisco.com/en/US/products/

25Note Use the Cisco Product Identification (CPI) tool to locate your product serial number before submitting a web or phonerequest for service. You c

26• Packet magazine is the Cisco Systems technical user magazine for maximizing Internet and networking investments. Eachquarter, Packet delivers cove

27

Corporate HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706USAwww.cisco.comTel: 408 526-4000800 553-NETS (6387)Fax: 408 526-

32 Related DocumentationUser DocumentationThe latest information is always online. To view or print an online document in its original format, click t

4Software Configuration GuideThe software configuration guideprovidesadditionaldetailedconfiguration information specific to Cisco IAD2430 series IADs

5Figure 1 Cisco IAD2430 Series Front PanelNote The Cisco IAD2432-24FXS is used to illustrate the examples in this guide.Figure 2 identifies the differ

6The Cisco IAD2432-24FXS is used to illustrate back-panel function options. See Figure 3 on page 6.Note Not all models have all functions.Figure 3 Bac

7Items Included with Cisco IAD2430 Series IADsThe following are included with each model in the series:• Rack-mount brackets for 19-inch rack; groundi

8IMPORTANT SAFETY INSTRUCTIONSWarningThis warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on anyeq

9Chassis Installation OptionsYou can set the chassis on a desktop, install it in a rack, or mount it on a wall.Tip Before proceeding, consider the loc