Cisco XR 12410 User Manual Page 198
- Page / 238
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 5 Maintaining the Router
Removing and Replacing AC and DC Power Subsystem Components
5-26
Cisco XR 12410 and Cisco XR 12810 Router Installation Guide
OL-17441-01
Troubleshooting a 2800 W DC PEM Installation
Use the following procedure to troubleshoot the DC PEM if it is not operating
properly after installation.
Step 1 Make sure the PEM is seated properly:
• Eject and reseat the PEM. Make sure:
–
The captive screw on the ejector lever is tightened securely.
–
The power switch is set to the on (1) position.
Step 2 Make sure the router is powered on and that all power cords are connected
properly.
Step 3 Check the PEM status indicators:
• F1LO (Feeder 1 Low) (flashing yellow)—Indicates that input connections to
the PDU (Feeder
1) were removed, or the input voltage is below the
minimum. Make sure that:
–
Power cords are securely attached to their PDU terminal studs.
–
Power cords are securely attached at the DC source end.
–
The source DC circuit breaker is switched on.
If the indicator is still flashing after you perform the above checks, replace
the power supply.
During normal operation, this indicator remains off.
• F2LO (Feeder2 Low) (flashing yellow)—Indicates that input connections to
the PDU (Feeder
2) are removed or the input voltage is below the minimum.
Make sure that:
–
Power cords are securely attached to their PDU terminal studs.
–
Power cords are securely attached at the DC source end.
–
The source DC circuit breaker is switched on.
If the indicator is still flashing after you perform the above checks, replace
the power supply.
During normal operation, this indicator remains off.
- Router Installation Guide 1
- CONTENTS 5
- B Site Log B-1 9
- Contents 10
- OL-17441-01 10
- Changes to This Document 11
- Audience 12
- Document Organization 12
- Document Conventions 13
- Product Overview 15
- AC and DC Power Subsystems 19
- Figure 1-4 AC PEM Components 20
- DC Power Supplies 21
- • 2 alarm cards 23
- Clock Scheduler Card 24
- Alarm Cards and Alarm Display 25
- Line Cards 28
- Route Processor 28
- BITS 1 AUX CONSOLE 33
- PRP-3 LEDs 34
- PRP Memory Components 37
- PRP SDRAM 41
- PRP SRAM 42
- PRP NVRAM 42
- PRP Flash Memory 42
- PRP-3 Compact Flash 43
- XR 12000 Series Router 44
- Horizontal cable 46
- Blower Module 47
- Figure 1-18 Cooling Air Flow 48
- Preparing for Installation 51
- Safety Guidelines 52
- Laser Safety 53
- Lifting Guidelines 55
- Site Requirement Guidelines 56
- Enclosed Rack 57
- Open Rack 57
- Telco Rack 58
- Center-mount 59
- Rack-mount bracket 59
- (attached to rack posts) 59
- 18.95 in 61
- 26.533 in 61
- 7.735 in 61
- 18.798 in 61
- Air Flow Guidelines 62
- Power Connection Guidelines 63
- AC-Powered Routers 64
- DC-Powered Routers 65
- Figure 2-8 DC Power Cable Lug 66
- Site Wiring Guidelines 70
- PRP Auxiliary Port Signals 74
- PRP Console Port Signals 75
- PRP Ethernet Connections 76
- 8 7 6 5 4 3 2 1 78
- Transmission 80
- Installation Overview 85
- Required Tools and Equipment 86
- 1 Front Door Latch 87
- Removing Power Supplies 89
- Removing DC PEMs 90
- Removing the Blower Module 91
- Verifying Rack Dimensions 99
- Reinstalling Power Supplies 109
- Reinstalling AC PEMs 110
- Reinstalling DC PEMs 111
- Air filter door 114
- Clock scheduler card 114
- FAST ETERNET 118
- Alarm display 125
- Troubleshooting Overview 132
- Identifying Startup Issues 134
- Figure 4-1 AC PEM Components 136
- Troubleshooting a DC PEM 140
- 1 3 4 52 6 146
- 1 3 4 52 146
- ETH 1ETH 0 148
- PRP Reset Switch 149
- PROCESSOR 150
- PRP-3 Alphanumeric LEDs 154
- Single PRP-3 Scenario 154
- Dual PRP-3 Scenario 156
- Troubleshooting Line Cards 159
- Figure 4-11 Cooling Air Flow 167
- Blower Module Operation 168
- Power Supply Operation 168
- Overtemperature Conditions 169
- Maintaining the Router 173
- Powering Off the Router 174
- OC-12/STM-4 ATM 178
- Subsystem Components 184
- Figure 5-7 AC PEM Components 186
- Figure 5-11) 192
- Rear panel 193
- AC horizontal trough 193
- DC horizontal trough 204
- Clear plastic covers 204
- Card Cage 212
- Technical Specifications 219
- • chassis only 220
- Router Specifications 224
- Site Log 225
- Appendix B Site Log 226
- Numerics 229
Related products and manuals for Hardware Cisco XR 12410
Hardware Cisco 3200 Series User Manual
(60 pages)
(60 pages)
Hardware Cisco LINKSYS WMP600N User Manual
(37 pages)
(37 pages)
Hardware Cisco MICA V110 User Manual
(10 pages)
(10 pages)
Hardware Cisco IDTA153 User Manual
(2 pages)
(2 pages)
Hardware Cisco OL-12812-01 User Manual
(18 pages)
(18 pages)
Hardware Cisco 2600-DC Series User Manual
(20 pages)
(20 pages)
Hardware Cisco 7300-6T3 User Manual
(54 pages)
(54 pages)
Hardware Cisco 3545 MCU User Manual
(56 pages)
(56 pages)
Hardware Cisco 3000 User Manual
(16 pages)
(16 pages)
Hardware Cisco 7206VXR NPE-400 User Manual
(22 pages)
(22 pages)
Hardware Cisco 3515 MCU12 User Manual
(54 pages)
(54 pages)
Hardware Cisco 340 User Manual
(62 pages)
(62 pages)
Hardware Cisco 2600XM Series User Manual
(28 pages)
(28 pages)
Hardware Cisco 4000 User Manual
(18 pages)
(18 pages)
Hardware Cisco OL-6109-01 User Manual
(22 pages)
(22 pages)
Hardware Cisco 3515 MCU24 User Manual
(44 pages)
(44 pages)
Hardware Cisco 3620 User Manual
(12 pages)
(12 pages)
Hardware Cisco 350 User Manual
(12 pages)
(12 pages)
© 2020, manymanuals.com. All rights reserved. | 0.144 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals