Cisco NTP-E157 User Manual Page 49
- Page / 167
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
User’s Manual of ISW-1022M Series and ISW-1033MT
49
Default User name: admin
Default Password: admin
3. After entering the username and password, the main screen appears as Figure 5-2.
Figure 5-2 Default main page
4. The Switch Menu on the left of the Web page let you access all the commands and statistics the Switch provides.
Now, you can use the Web management interface to continue the switch management or manage the Managed Industrial
Switch by Web interface. The Switch Menu on the left of the web page let you access all the commands and statistics the
Managed Industrial Switch provides.
1. It is recommended to use Internet Explore 6.0 or above to access Managed Industrial
Switch.
2. The changed IP address take effect immediately after click on the Save button, you need to
use the new IP address to access the Web interface.
3. For security reason, please change and memorize the new password after this first setup.
4. Only accept command in lowercase letter under web interface.
- User’s Manual 1
- Trademarks 2
- Disclaimer 2
- WEEE Warning 2
- TABLE OF CONTENTS 3
- 1. Introduction 6
- 1.3 Product Features 7
- 1.4 Product Specification 10
- 2. Installation 18
- 2.1.2 Front / Rear Panel 21
- 2.1.3 Top View 24
- 2.1.4 LED Indicators 25
- 2.2 Install the Switch 30
- 2.2.2 DIN-Rail Mounting 31
- 1 2 3 4 5 6 33
- Power 2 Power 1 33
- - + - + 33
- Connect the fiber cable 37
- 3. Network Application 39
- 3.1 Rapid Ring Application 40
- 3.3 Dual Homing Application 41
- 4. Console Management 42
- Console login interface 44
- 4.4 CLI Management 45
- 4.5 Commands Level 46
- 5. Web-Based Management 47
- 5.2 Requirements 48
- 5.3 Logging on the switch 48
- 5.4 System 50
- 5.4.1 System Information 51
- 5.4.2 IP Configuration 52
- 5.4.3 DHCP Server 53
- 5.4.3.2 Client Entries 54
- 5.4.3.3 Port and IP Bindings 55
- 5.4.4 TFTP 56
- 5.4.4.3 Backup Configuration 57
- 5.4.5 System Event Log 58
- 5.4.6 Fault Relay Alarm 62
- 5.4.7 SNTP Configuration 63
- UTC Timezone: 64
- 5.4.8 IP Security 66
- 5.4.9 User Authentication 67
- 5.5 Port Management 68
- 5.5.2 Port Control 69
- 5.5.3 Port Trunk 70
- 5.5.3.1 Aggregator setting 71
- LACP disabled 72
- LACP enabled 73
- Switch 1 configuration 73
- Switch 2 configuration 74
- 5.5.3.3 State Activity 76
- 5.5.4 Port Mirroring 77
- 5.5.5 Rate Limiting 78
- 5.6 Protocol 79
- New Tagged Packet 81
- Original Ethernet 81
- Priority CFI VLAN ID 81
- 5.6.1.2 VLAN Configuration 82
- 5.6.1.3 Port-based VLAN 82
- 5.6.1.4 802.1Q VLAN 84
- Group Configuration 89
- 5.6.2 Rapid Spanning Tree 90
- 5.6.2.2 RSTP Parameters 92
- 5.6 2.3 Illustration of STP 94
- 5.6.2.5 Port Configuration 98
- 5.6.3 SNMP Configuration 100
- 5.6.3.2 Trap Configuration 101
- 5.6.3.3 SNMPV3 Configuration 102
- Context Table 102
- User Table 102
- Group Table 103
- Access Table 103
- MIBview Table 104
- 5.6.4 QoS Configuration 105
- 5.6.4.2 Port-based Priority 107
- 5.6.4.3 COS Configuration 107
- 5.6.4.4 TOS Configuration 108
- 5.6.5 IGMP Snooping 110
- Type Response Time 112
- Non-Member 113
- Delaying Member Idle Member 113
- 5.6.5.2 IGMP Configuration 114
- 5.6.6 X-Ring 115
- 5.6.6.4 X-Ring Configuration 117
- 5.7 Security 119
- 5.7.1.2 System Configuration 122
- 5.7.1.3 Port Configuration 123
- 5.7.1.4 Misc Configuration 124
- 5.7.2 MAC Address Table 125
- 5.7.2.2 MAC Filtering 126
- 5.7.2.3 All MAC Addresses 127
- 5.7.2.4 Multicast Filtering 128
- 5.8.1 Digital Input 129
- 5.8.2 Digital Output 130
- 5.9 Power over Ethernet 131
- 5.10 Factory Default 135
- 5.11 Save Configuration 135
- 5.12 System Reboot 136
- 6. Command Sets 137
- 6.2 Port Commands Set 139
- 6.3 Trunk Commands Set 141
- 6.4 VLAN Commands Set 142
- 6.6 QOS Commands Set 145
- 6.7 IGMP Commands Set 145
- 6.9 SNMP Commands Set 146
- 6.11 802.1x Commands Set 149
- 6.12 TFTP Commands Set 150
- 6.14 SNTP Commands Set 152
- 6.15 X-ring Commands Set 153
- 6.16 PoE Command Set 153
- 7. SWITCH OPERATION 155
- 7.5 Auto-Negotiation 156
- What is PoE? 157
- POWER SOURCING 158
- EQUIPMENT (PSE) 158
- POWER DEVIC 158
- The PoE Provision Process 159
- Start-up 160
- Operation 160
- 12345678 162
- Appendix B Troubles shooting 163
- EC Declaration of Conformity 164
Related products and manuals for Network switches Cisco NTP-E157
Network switches Cisco IGX 8 Specifications
(298 pages)
(298 pages)
Network switches Cisco 8600 Specifications
(129 pages)
(129 pages)
Network switches Cisco 3040 Specifications
(99 pages)
(99 pages)
(5 pages)
Network switches Cisco CGS 2520 User Manual
(105 pages)
(105 pages)
© 2020, manymanuals.com. All rights reserved. | 0.021 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals