Cisco MWR-1900-27 Specifications Page 429
- Page / 814
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
B-193
Cisco MWR 2941 Mobile Wireless Edge Router Software Configuration Guide, Release 12.2(33)MRB
OL-21227-02
Appendix B Cisco MWR 2941 Router Command Reference
load-interval
Examples In the following example, the default 5-minute average is set to a 30-second average. A burst in traffic
that would not trigger a dial backup for an interface configured with the default 5-minute interval might
trigger a dial backup for this interface that is set for a shorter, 30-second interval.
Router(config)# interface serial 0
Router(config-if)# load-interval 30
Related Commands Command Description
show interfaces Displays ALC information.
- Release 12.2(33)MRB 1
- CONTENTS 3
- Contents 4
- About This Guide 9
- Audience 10
- Organization 10
- Conventions 10
- Related Documentation 11
- Guidelines 12
- OL-21227-02 13
- Introduction 14
- Features 15
- Features 16
- Limitations 17
- E2E1 E2E1 18
- Edge port 18
- Blocked port 18
- Link failure 18
- Link Integrity 19
- Fast Convergence 19
- VLAN Load Balancing 20
- Spanning Tree Interaction 21
- REP Ports 21
- Overview 22
- Link OAM 23
- Link Monitoring 24
- Remote Failure Indication 24
- Remote Loopback 25
- OAM Messages 25
- Clocking and Timing 26
- PTP Domains 27
- Pseudowire-based Clocking 28
- Synchronous Ethernet 28
- Routing Protocols 29
- Multicast Routing 30
- IP Multicast Group Addressing 32
- IP Multicast Address Scoping 33
- Layer 2 Multicast Addresses 34
- IP Multicast Delivery Modes 34
- Source Specific Multicast 35
- Multicast Group Modes 36
- Rendezvous Points 37
- Bootstrap Router 38
- Anycast RP 39
- Multicast Forwarding 40
- Source Tree Advantage 41
- Shared Tree Advantage 42
- Reverse Path Forwarding (RPF) 42
- RPF Check 43
- MLPPP Optimization Features 44
- Cell Site Points-of-Presence 45
- Quality of Service 46
- Network Management Features 47
- Limitations and Restrictions 48
- Cisco IOS Software Basics 51
- Understanding Command Modes 52
- Undoing a Command or Feature 53
- First-Time Configuration 55
- Slot and Port Numbering 56
- Setup Command Facility 57
- Configuring Global Parameters 58
- Completing the Configuration 60
- Configuration Sequence 63
- Summary of Steps 64
- Enabling the Interface 68
- Defining a Range Macro 69
- Configuring Stacking 73
- Configuring VLANs 74
- Configuring a VTP Server 75
- Configuring a VTP Client 76
- Disabling VTP 76
- Default REP Configuration 77
- REP Configuration Guidelines 77
- Configuring REP Interfaces 79
- Monitoring REP 82
- Understanding Ethernet CFM 83
- Maintenance Domain 84
- Port interior to domain 85
- Maintenance 85
- Port at edge of domain 85
- Maintenance Point 86
- CFM Messages 88
- Cross-Check Function 89
- SNMP Traps 90
- CFM over Bridge Domains 91
- Configuring Ethernet CFM 92
- Configuring PTP Clocking 101
- Configuring the PTP Mode 102
- Configuring MLPPP Backhaul 111
- Configuring E1 Controllers 112
- Configuring T1 Controllers 114
- Configuring ATM IMA 115
- Creating a Multilink Bundle 117
- Configuring PFC and ACFC 117
- Configuring PFC 118
- Configuring ACFC 118
- MLPPP Offload 120
- Configuring Routing Protocols 121
- Configuring BFD 121
- Configuring BFD for BGP 123
- Configuring BFD for IS-IS 123
- Configuring IP Multicast 126
- Configuring Multicast VPN 133
- Configuring Pseudowire 135
- Using Pseudowire Classes 136
- Using CEM Classes 137
- Configuring GRE Tunneling 138
- Using Pseudowire Labels 139
- Configuring a Backup Peer 140
- Configuring the Controller 142
- Configuring an IMA Interface 143
- Optional Configurations 148
- Configuring VLAN Mode 149
- QoS Limitations 150
- Statistics Limitations 151
- Propagation Limitations 151
- Classification Limitations 151
- Configuration Sequence 152
- Marking Limitations 153
- Queuing Limitations 154
- Rate Limiting Limitations 154
- Sample QoS Configuration 155
- Configuring Classification 157
- Configuring Marking 159
- Configuring Shaping 165
- Usage Notes 168
- Saving Configuration Changes 169
- Configuring SNMP Support 170
- Process Overview 178
- Configuring a DHCP Server 178
- Configuring a TFTP Server 179
- Verifying the Configuration 180
- Sample Configurations 181
- Pseudowire Configurations 182
- TDM over MPLS Configuration 194
- ATM over MPLS Configuration 197
- GRE Tunneling Configurations 206
- Routing Sample Configurations 207
- BGP with BFD 211
- IS-IS with BFD 214
- Source-Specific Multicast 217
- PTP Sample Configurations 218
- PTP Redundancy 223
- PTP Hybrid Mode 224
- PTP Hot Standby Master Clock 224
- PTP Input Timing 225
- PTP Output Timing 226
- QoS Sample Configurations 228
- Switchport Priority 229
- Classification and Marking 229
- MPLS Bit Marking 230
- Priority Queuing 231
- Sample Configurations 236
- APPENDIX 237
- address-family ipv4 (BGP) 245
- MDT Example 246
- atm vc-per-vp 250
- Configuring a Policy Map 257
- Restrictions 258
- bfd all-interfaces 261
- bfd interval 263
- cdp enable 267
- class (policy-map) 270
- Policy Map Configuration Mode 271
- Class Characteristics 271
- Predefined Default Class 271
- Tail Drop or WRED 271
- Fragments 272
- class cem 275
- class-map 276
- clear ethernet cfm errors 283
- clock update-calendar 289
- controller 290
- cns config initial 291
- cns config partial 294
- cns config retrieve 297
- cns event 300
- cns exec 303
- If ID Choice Is Anything Else 305
- Unique Device Identifier 306
- cns image password 308
- cns image retrieve 309
- cns password 312
- cns trusted-server 315
- dscp 318
- encapsulation (ATM) 321
- SNAP Encapsulation Example 322
- ethernet cfm cc 323
- • Globally (per device) 324
- • For a maintenance domain 324
- • For a particular level 327
- • For a particular VLAN 327
- ethernet cfm domain level 328
- ethernet cfm enable 330
- ethernet cfm logging 332
- Syntax Description 334
- 2. Service within the domain 340
- ethernet lmi 349
- ethernet lmi global 351
- ethernet oam 353
- idle-pattern 381
- interface atm ima 385
- ip igmp join-group 386
- ip igmp query-interval 388
- ip igmp static-group 392
- ip igmp version 394
- Command Description 397
- ip multicast-routing 398
- ip ospf bfd 401
- • proxy-register 402
- • list access-list 402
- • route-map map-name 402
- Dense Mode 403
- Passive Mode 403
- Sparse Mode 403
- Sparse-Dense Mode 404
- ip pim bsr-border 407
- ip pim bsr-candidate 408
- ip pim query-interval 410
- ip pim register-source 413
- ip pim rp-address 415
- ip pim rp-candidate 417
- • interval seconds 419
- • bidir 419
- ip pim send-rp-discovery 421
- ip pim ssm 424
- keepalive 426
- Keepalive Time Interval 427
- Line Failure 427
- Dropped Packets 427
- load-interval 428
- match any 431
- match atm clp 432
- DSCP Values 436
- Match Packets on DSCP Values 437
- match ip dscp 438
- match mpls experimental 440
- • match access-group 441
- • match input-interface 441
- • match mpls experimental 441
- • match protocol 441
- match precedence 442
- Precedence Values and Names 443
- IPv4-Specific Traffic Match 443
- IPv6-Specific Traffic Match 444
- match qos-group 445
- Support Restrictions 447
- match vlan (QoS) 448
- mdt data 450
- mep archive-hold-time 454
- mep crosscheck mpid vlan 456
- ATM Mode Example 459
- CAS Mode Example 460
- Router(config)# no mpls ip 464
- mpls label 468
- mpls label range 469
- mpls ldp router-id 472
- neighbor (OSPF) 475
- Release 12.2(33)SRB 476
- neighbor remote-as (BGP) 478
- network-clock-select 481
- payload-size 489
- ping ethernet 490
- ping ethernet vlan 492
- police (percent) 494
- All Supported Platforms 495
- Hierarchical Policy Maps 496
- How Bandwidth Is Calculated 497
- police (policy map) 499
- • exceed-action is drop 503
- • violate-action is drop 503
- police (two rates) 505
- Token Buckets 506
- Updating Token Buckets 507
- Marking Traffic 507
- Two-Rate Policing 508
- Syntax for Percent 510
- policy-map 514
- priority 518
- protocol (ATM) 521
- Command Application 522
- • Data encapsulation type 524
- • Control protocol 524
- • 3—1 packet every 8 seconds 526
- • 2—1 packet every 4 seconds 526
- • 1—1 packet every 2 seconds 526
- • 0—1 packet every second 526
- ptp announce 527
- ptp delay-req interval 531
- ptp delay-req unicast 534
- Related Commands 538
- ptp master 540
- ptp output 543
- ptp slave 548
- ptp sync interval 550
- queue-limit 556
- Weighted Fair Queueing 557
- random-detect 559
- Keywords 560
- Availability 560
- WRED Functionality 560
- WRED in a Policy Map 560
- random-detect cos-based 565
- random-detect dscp 569
- Specifying the DSCP Value 570
- Class Selector Values 571
- Default Values 571
- rep admin vlan 585
- rep block port 586
- rep preempt delay 590
- • SPAN destination port 592
- • Private VLAN port 592
- • Tunnel port 592
- rep segment 594
- router bgp 596
- router isis 601
- router ospf 604
- service-policy 607
- the following adapters: the 616
- set cos 618
- to specify the from-field 619
- set cos-inner cos 624
- set discard-class 625
- • EF (expedited forwarding) 627
- Precedence Value and Queueing 628
- set fr-de 631
- set ip dscp 632
- 2. ip tos reflect 636
- 3. ip tos tos-value 636
- set ip tos (route-map) 644
- set network-clocks 646
- Command Compatibility 647
- Bit Settings 647
- Precedence Value 648
- set precedence 649
- set qos-group 650
- shape 653
- shape (percent) 655
- Committed Information Rate 656
- shape (policy-map class) 658
- shape max-buffers 662
- show adjacency 663
- show cem circuit 668
- show cem platform 670
- Last cleared 6d02h 670
- show connection 671
- • Interface name and number 672
- show controller 674
- • Identifier (group ID) 676
- show cns config stats 677
- show cns event stats 681
- • Domain name 688
- • Domain index 688
- • Domain level 688
- show ethernet cfm domain 690
- show ethernet cfm errors 691
- Field Description 697
- show ethernet lmi 710
- Reliability Errors 713
- Protocol Errors 714
- • Local and remote OAM mode 716
- • Remote platform identity 716
- • Remote loopback events 719
- show ethernet oam status 724
- show ethernet oam summary 726
- show interfaces rep 727
- show ip mroute 730
- show mpls l2transport vc 734
- show network-clocks 741
- show platform hardware 743
- show policy-map 744
- Traffic Policing: Example 746
- Tunnel Marking: Example 751
- show policy-map interface 752
- ATM Shared Port Adapter 753
- (continued) 758
- Traffic Shaping: Example 763
- Offset From Master: 0 771
- Priority1: 128 773
- Current UTC offset: 33 775
- show rep topology 776
- show xconnect 779
- switchport backup 793
- tunnel destination 798
- tunnel source 799
- GRE Tunneling Example 800
- tx-limit 801
- xconnect 803
- Activating the Primary Member 807
- Activating the Backup Member: 807
- 4-3 813
- 4-1 813
- 4-46 813
Related products and manuals for Networking Cisco MWR-1900-27
Networking Cisco WRT120N User Manual
(44 pages)
(44 pages)
Networking Cisco EZXS16W User Manual
(2 pages)
(2 pages)
Networking Cisco ATA-186 User Manual
(8 pages)
(8 pages)
Networking Cisco SPA2102-AU User Manual
(5 pages)
(5 pages)
Networking Cisco SCE 1000 2xGBE User's Guide
(490 pages)
(490 pages)
Networking Cisco 10005 Installation Guide
(46 pages)
(46 pages)
Networking Cisco 6260 Installation Guide
(244 pages)
(244 pages)
Networking Cisco 815 Specifications
(28 pages)
(28 pages)
Networking Cisco WES610N User Manual
(21 pages)
(21 pages)
Networking Cisco 510 User Manual
(2 pages)
(2 pages)
Networking Cisco WPC54GS User's Guide
(83 pages)
(83 pages)
© 2020, manymanuals.com. All rights reserved. | 0.065 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals