Cisco OL-5490-01 User's Guide Page 52
- Page / 92
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
4-8
VPN Client User Guide for Mac OS X
OL-5490-01
Chapter 4 Configuring Connection Entries
Backup Servers
• When this parameter is disabled, all traffic from your client system goes through the IPSec
connection to the secure gateway.
If the local LAN you are using is not secure, you should not enable local LAN access. For example, do
not enable this feature when you are using a local LAN in a hotel or airport.
To enable this feature, check the Allow Local LAN Access check box on the VPN Client. You must also
enable this feature on the VPN device you are connecting to.
Peer Response Timeout
The VPN Client uses a keepalive mechanism called Dead Peer Detection (DPD) to check the availability
of the VPN device on the other side of an IPSec tunnel. If the network is unusually busy or unreliable,
you may need to increase the number of seconds to wait before the VPN Client decides that the peer is
no longer active. The default number of seconds to wait before terminating a connection is 90 seconds.
The minimum number of seconds you can configure is 30 seconds and the maximum is 480 seconds.
To adjust the setting, enter the number of seconds in the Peer response timeout field.
The VPN Client continues to send DPD requests every 5 seconds, until it reaches the number of seconds
specified by the Peer response timeout value.
Backup Servers
The private network you are connecting to might include one or more backup VPN devices (servers) to
use if the primary server is not available. The list of available backup servers is pushed to the VPN Client
when the connection is established, or you can add a backup server to the list manually.
The list of existing backup servers is found on the Backup Servers tab for each connection entry. Your
network administrator can provide information regarding backup servers.
To use backup servers, you must enable this parameter.
To enable backup servers:
Step 1 Open the VPN Client application.
Step 2 Select a connection entry.
Step 3 Click Modify at the top of the VPN Client window. The VPN Client Properties dialog box appears.
Step 4 Click the Backup Servers tab (Figure 4-6).
- Customer Order Number: 1
- Text Part Number: OL-5490-01 1
- CONTENTS 3
- Contents 4
- 7 Managing the VPN Client 7-1 6
- About This Guide 7
- Related Documentation 8
- Terminology 8
- Document Conventions 8
- Obtaining Documentation 9
- Ordering Documentation 10
- Documentation Feedback 10
- Cisco.com 10
- Technical Assistance Center 11
- Cisco TAC Escalation Center 12
- Understanding the VPN Client 13
- VPN Client Overview 14
- VPN Client Features 15
- OL-5490-01 16
- Authentication Features 17
- IPSec Features 17
- VPN Client IPSec Attributes 18
- • IPSec over UDP (NAT/PAT) 19
- • IPSec over TCP (NAT/PAT) 19
- Installing the VPN Client 21
- Preconfiguring the VPN Client 22
- • Certificate enrollment 23
- Step 4 Click OK 25
- Introduction 26
- Uninstalling the VPN Client 32
- Navigating the User Interface 35
- Choosing a Run Mode 36
- Operating in Simple Mode 36
- Main Menus—Simple Mode 37
- Operating in Advanced Mode 38
- Main Tabs—Advanced Mode 39
- Main Menus—Advanced Mode 40
- Status Menu 41
- Certificates Menu 41
- Right-Click Menus 42
- Creating a Connection Entry 45
- Figure 4-1 VPN Client Window 46
- Authentication Methods 47
- Mutual Group Authentication 48
- Certificate Authentication 48
- Transport Parameters 50
- Enable Transport Tunneling 51
- Transparent Tunneling Mode 51
- Allow Local LAN Access 51
- Backup Servers 52
- Establishing a VPN Connection 55
- Establishing a Connection 56
- Shared Key Authentication 57
- RADIUS Server Authentication 58
- SecurID Authentication 59
- Using Digital Certificates 60
- Using the Certificate Store 61
- Enrolling Certificates 62
- Managing Enrollment Requests 65
- Importing a Certificate 67
- Viewing a Certificate 67
- Exporting a Certificate 69
- Deleting a Certificate 70
- Verifying a Certificate 71
- Step 5 Click OK 72
- Managing the VPN Client 73
- Modifying a Connection Entry 74
- Deleting a Connection Entry 75
- Event Logging 76
- Clear Logging 77
- Set Logging Options 77
- Figure 7-5 Log Settings 78
- Opening the Log Window 79
- Viewing Statistics 80
- Tunnel Details 81
- Route Details 82
- Notifications 83
Related products and manuals for Networking Cisco OL-5490-01
Networking Cisco WRT54GP2 User's Guide
(94 pages)
(94 pages)
Networking Cisco C3270ENC-K9 User Manual
(9 pages)
(9 pages)
Networking Cisco uBR10-MC5X20S User Manual
(20 pages)
(20 pages)
Networking Cisco Spam User's Guide
(20 pages)
(20 pages)
Networking Cisco EPC2607 User Manual
(28 pages)
(28 pages)
Networking Cisco 12810 Specifications
(30 pages)
(30 pages)
Networking Cisco WRVS4400N - Small Business Wireless-N Gigabit Security Router User's Guide
(180 pages)
(180 pages)
Networking Cisco EA-Series User's Guide
(144 pages)
(144 pages)
Networking Cisco 888E User Manual
(18 pages)
(18 pages)
Networking Cisco 12016 Specifications
(36 pages)
(36 pages)
Networking Cisco DPC2203 User's Guide
(58 pages)
(58 pages)
Networking Cisco SD2008T-NA User Manual
(28 pages)
(28 pages)
© 2020, manymanuals.com. All rights reserved. | 0.017 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals