Cisco XR 12000 Series User Manual Page 133
- Page / 148
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
5-5
Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide
OL-17438-04
Chapter 5 Installing and Removing a Shared Port Adapter
Checking the Installation
• If a SIP or SPA is replaced with a module of the same type (as in an OIR or hardware swap), the
previous configuration will be reinstated when the SIP or SPA becomes active.
• If a SIP or SPA has not been previously installed in the same slot or subslot, then the configuration
for all associated interfaces will be empty.
Note New interfaces are not available until you configure them.
Step 3 If the SIPs and SPAs have not become active within three minutes, refer to the system console messages
as follows:
• If a SIP or SPA is undergoing an FPD upgrade, then console messages will indicate that the FPD
process has been initiated. The upgrade process might take several minutes. Use the show fpd
upgrade process command to obtain information about the FPD process. SIPs or SPAs that undergo
an FPD upgrade will automatically be rebooted. Return to
Step 1.
• If there is no indication that an FPD upgrade is underway, see Chapter 6, “Troubleshooting the
Installation.”
Using show Commands to Verify SIP and SPA Status
The following procedure uses show commands to verify that the new SPAs are configured and operating
correctly.
Step 1 Use the show running-config command to display the system configuration. Verify that the
configuration includes the new SPA interfaces.
Step 2 Display all of the current SPAs and a summary of their status using the show hw-module subslot oir
command.
Step 3 Display information about the installed SIPs using the show diag command.
Step 4 Use the show hw-module subslot fpd command to verify the FPD version information of the SPAs
installed in the system.
Note If a SPA does not meet the minimum version required, it will automatically be updated. If the
update fails, the failing module will be powered down and an error message will be reported on
the system console.
Step 5 Finally, you can use the show version command to obtain a few details on the installed SIPs and
interfaces available.
Using show Commands to Display SPA Information
Table 5-1 describes the show commands you can use to display SPA information.
- Hardware Installation Guide 1
- CONTENTS 3
- Contents 4
- Changes to This Document 9
- OL-17438-04 10
- Objectives 11
- Organization 11
- Related Documentation 12
- Interface Processors 13
- Router Hardware Installation 14
- Supported Platforms 15
- SIP Summary 16
- Cisco XR 12000 SIP-600 LEDs 18
- Cisco XR 12000 SIP-401 LEDs 21
- Cisco XR 12000 SIP-501 LEDs 24
- 10-Port Gigabit Ethernet SPA 26
- Cisco XR 12000 SIP-601 LEDs 27
- Port Adapters 31
- SPA Summary 32
- Bandwidth Oversubscription 33
- Bandwidth Oversubscription 34
- Figure 2-4 RJ-45 Connector 40
- 8-Port FastEthernet SPA LEDs 41
- RJ-45 connector 42
- XFP Connections 45
- SPA-2X1GE 47
- SPA-2X1GE-V2 48
- SFP Module Connections 49
- SFP-GE-S Modules 51
- SFP-GE-L Modules 51
- SFP-GE-Z Modules 51
- SFP-GE-T Modules 51
- SPA-1XCHSTM1/OC3 60
- Figure 2-18 SFP Optics Module 62
- Figure 2-19 LC Type Cables 62
- Figure 2-21 SFP Optics Module 64
- Figure 2-24 SFP Optics Module 67
- Figure 2-25 LC Type Cables 67
- Connector, and Cables 70
- Figure 2-28 SPA Mate Cables 71
- OC-192 Module Connections 74
- Mate Interface Cables 75
- Figure 2-33 SFP Optics Module 78
- Figure 2-34 LC-Type Cable 78
- OC-3 Module Connections 79
- SPA-8XOC12-POS 80
- OC-12 Module Connections 84
- SPA-1XOC12-POS 85
- Figure 2-40 LC-Type Cable 88
- Figure 2-43 SPA Mate Cables 91
- SPA-2XOC48-POS/RPR 92
- Modules, and Connectors 93
- OC-48 Module Connections 94
- 2-Port OC48-POS/RPR SPA LEDs 95
- Connectors 97
- IPSec VPN SPA LEDs 98
- Figure 2-51 SFP Optics Module 100
- Figure 2-54 SFP Optics Module 103
- SPA-2CHT3-CE-ATM 104
- Cable Installation 108
- SPA Cable Pinouts 108
- RJ-45 Cable Pinouts 111
- Patch Panel Cabling 111
- Connectors, and Cables 114
- ACTIVE/LINK 116
- XFP Module Connections 117
- SPA Interface Processor 119
- Telephone Wiring Guidelines 120
- Laser/LED Safety 120
- Required Tools and Equipment 122
- Processor 123
- Removing and Installing a SIP 124
- Removing a SIP 125
- Installing a SIP 127
- Handling SPAs 129
- Online Insertion and Removal 130
- SPA Installation and Removal 130
- Cleaning Optical Devices 131
- Checking the Installation 132
- Checking the Installation 133
- Troubleshooting the SIP 137
- Using debug Commands 137
- Packing a SIP for Shipment 138
- Packing a SPA for Shipment 139
- Packing a SPA for Shipment 140
- GLOSSARY 141
- Glossary 142
- Numerics 143
Related products and manuals for Hardware Cisco XR 12000 Series
Hardware Cisco 15310-MA User Manual
(10 pages)
(10 pages)
Hardware Cisco 7100 Series User Manual
(24 pages)
(24 pages)
Hardware Cisco 12012 User Manual
(34 pages)
(34 pages)
Hardware Cisco 2600 User Manual
(32 pages)
(32 pages)
Hardware Cisco 3725 User Manual
(22 pages)
(22 pages)
Hardware Cisco WRT320N User Manual
(53 pages)
(53 pages)
Hardware Cisco 7200 VXR User Manual
(64 pages)
(64 pages)
Hardware Cisco 1600 User Manual
(13 pages)
(13 pages)
Hardware Cisco 12406 User Manual
(36 pages)
(36 pages)
Hardware Cisco WES610N User Manual
(546 pages)
(546 pages)
Hardware Cisco 3500 Series User Manual
(8 pages)
(8 pages)
Hardware Cisco 1005 User Manual
(6 pages)
(6 pages)
Hardware Cisco 2600 Series User Manual
(10 pages)
(10 pages)
Hardware Cisco 1720 User Manual
(12 pages)
(12 pages)
Hardware Cisco 3660 User Manual
(10 pages)
(10 pages)
Hardware Cisco 32369 User Manual
(52 pages)
(52 pages)
Hardware Cisco (VIP6-80) User Manual
(40 pages)
(40 pages)
Hardware Cisco ASA 5505 User Manual
(199 pages)
(199 pages)
© 2020, manymanuals.com. All rights reserved. | 0.656 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals