Cisco XR 12000 Series User Manual Page 70
- Page / 148
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
2-40
Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide
OL-17438-04
Chapter 2 Overview: Cisco XR 12000 Series Router Shared Port Adapters
1-Port OC-192/STM-64 POS SPA Overview
• RFC 1213, Management Information Base (MIB) for Network Management of TCP/IP-Based
Internets:MIB II
1-Port OC-192/STM-64 POS/RPR SPA Fixed Optical Transceiver, 40-Pin
Connector, and Cables
The 1-Port OC-192/STM-64 POS/RPR SPA uses fixed optical transceivers, one for receive (RX) and one
for transmit (TX), for SONET and SDH connection to the network. In Cisco IOS Release
12.0(31)S,
only long-reach (LR) optics are supported.
Cisco Systems qualifies the optics that are approved for use with its SPAs. As of Cisco IOS Release
12.0(31)S and Cisco IOS XR Software Release 3.2, the XFP-10GLR-OC192SR and the
XFP-10GER-OC192IR are the only optical transceiver modules qualified for use.
The 1-Port OC-192/STM-64 POS/RPR SPA uses single-mode SC-type connectors:
• Single-mode—9.95 Gbps, OC-192 optical fiber (SONET STS-192 or SDH STM-64c)
Use a single-mode optical fiber that has a modal-field diameter of 8.7 ±0.5 microns. (Nominal diameter
is approximately 10/125 microns.)
Use a single-mode optical fiber cable to connect your router to a network.
Note The 40-pin connector on the 1-Port OC-192/STM-64 POS/RPR SPA is used for resilient packet ring
(RPR) connections.
Figure 2-27 shows the cable type for use with the fixed optical transceiver module on the 1-Port
OC-192/STM-64 POS/RPR SPA.
Figure 2-27 SC-Type Connectors for the Fixed Optical Transceivers
Mate Interface Cables
The 1-Port OC-192/STM-64 POS/RPR SPA supports two mate interface configurations:
• Mate between two OC-192 SPAs in the same SIP
• Mate between two OC-192 SPAs in adjacent SIPs
Two 1-Port OC-192/STM-64 POS/RPR SPAs are connected using a 40–pin connector copper mate cable.
The length of the cables allow only two possible connection scenarios, next slot horizontal and same slot
vertical. This assumes that the chassis is mounted vertically.
Figure 2-28 shows the mate cables used to
connect the SPAs.
38547
- Hardware Installation Guide 1
- CONTENTS 3
- Contents 4
- Changes to This Document 9
- OL-17438-04 10
- Objectives 11
- Organization 11
- Related Documentation 12
- Interface Processors 13
- Router Hardware Installation 14
- Supported Platforms 15
- SIP Summary 16
- Cisco XR 12000 SIP-600 LEDs 18
- Cisco XR 12000 SIP-401 LEDs 21
- Cisco XR 12000 SIP-501 LEDs 24
- 10-Port Gigabit Ethernet SPA 26
- Cisco XR 12000 SIP-601 LEDs 27
- Port Adapters 31
- SPA Summary 32
- Bandwidth Oversubscription 33
- Bandwidth Oversubscription 34
- Figure 2-4 RJ-45 Connector 40
- 8-Port FastEthernet SPA LEDs 41
- RJ-45 connector 42
- XFP Connections 45
- SPA-2X1GE 47
- SPA-2X1GE-V2 48
- SFP Module Connections 49
- SFP-GE-S Modules 51
- SFP-GE-L Modules 51
- SFP-GE-Z Modules 51
- SFP-GE-T Modules 51
- SPA-1XCHSTM1/OC3 60
- Figure 2-18 SFP Optics Module 62
- Figure 2-19 LC Type Cables 62
- Figure 2-21 SFP Optics Module 64
- Figure 2-24 SFP Optics Module 67
- Figure 2-25 LC Type Cables 67
- Connector, and Cables 70
- Figure 2-28 SPA Mate Cables 71
- OC-192 Module Connections 74
- Mate Interface Cables 75
- Figure 2-33 SFP Optics Module 78
- Figure 2-34 LC-Type Cable 78
- OC-3 Module Connections 79
- SPA-8XOC12-POS 80
- OC-12 Module Connections 84
- SPA-1XOC12-POS 85
- Figure 2-40 LC-Type Cable 88
- Figure 2-43 SPA Mate Cables 91
- SPA-2XOC48-POS/RPR 92
- Modules, and Connectors 93
- OC-48 Module Connections 94
- 2-Port OC48-POS/RPR SPA LEDs 95
- Connectors 97
- IPSec VPN SPA LEDs 98
- Figure 2-51 SFP Optics Module 100
- Figure 2-54 SFP Optics Module 103
- SPA-2CHT3-CE-ATM 104
- Cable Installation 108
- SPA Cable Pinouts 108
- RJ-45 Cable Pinouts 111
- Patch Panel Cabling 111
- Connectors, and Cables 114
- ACTIVE/LINK 116
- XFP Module Connections 117
- SPA Interface Processor 119
- Telephone Wiring Guidelines 120
- Laser/LED Safety 120
- Required Tools and Equipment 122
- Processor 123
- Removing and Installing a SIP 124
- Removing a SIP 125
- Installing a SIP 127
- Handling SPAs 129
- Online Insertion and Removal 130
- SPA Installation and Removal 130
- Cleaning Optical Devices 131
- Checking the Installation 132
- Checking the Installation 133
- Troubleshooting the SIP 137
- Using debug Commands 137
- Packing a SIP for Shipment 138
- Packing a SPA for Shipment 139
- Packing a SPA for Shipment 140
- GLOSSARY 141
- Glossary 142
- Numerics 143
Related products and manuals for Hardware Cisco XR 12000 Series
Hardware Cisco 15310-MA User Manual
(10 pages)
(10 pages)
Hardware Cisco 7100 Series User Manual
(24 pages)
(24 pages)
Hardware Cisco 12012 User Manual
(34 pages)
(34 pages)
Hardware Cisco 2600 User Manual
(32 pages)
(32 pages)
Hardware Cisco 3725 User Manual
(22 pages)
(22 pages)
Hardware Cisco WRT320N User Manual
(53 pages)
(53 pages)
Hardware Cisco 7200 VXR User Manual
(64 pages)
(64 pages)
Hardware Cisco 1600 User Manual
(13 pages)
(13 pages)
Hardware Cisco 12406 User Manual
(36 pages)
(36 pages)
Hardware Cisco WES610N User Manual
(546 pages)
(546 pages)
Hardware Cisco 3500 Series User Manual
(8 pages)
(8 pages)
Hardware Cisco 1005 User Manual
(6 pages)
(6 pages)
Hardware Cisco 2600 Series User Manual
(10 pages)
(10 pages)
Hardware Cisco 1720 User Manual
(12 pages)
(12 pages)
Hardware Cisco 3660 User Manual
(10 pages)
(10 pages)
Hardware Cisco 32369 User Manual
(52 pages)
(52 pages)
Hardware Cisco (VIP6-80) User Manual
(40 pages)
(40 pages)
Hardware Cisco ASA 5505 User Manual
(199 pages)
(199 pages)
© 2020, manymanuals.com. All rights reserved. | 2.950 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals