Cisco 3560 User Manual Page 102
- Page / 120
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
C-2
Catalyst 3560 Switch Hardware Installation Guide
OL-6337-07
Appendix C Connecting to DC Power
Connecting to DC Power
Caution The Catalyst 3560V2-24TS-SD switch is suitable only for intrabuilding or nonexposed wiring
connections.
Preparing for Installation
Locate the ground lug and the two number-10-32 screws on the switch rear panel and the DC terminal
block plug in the DC-switch accessory kit.
Obtain these necessary tools and equipment:
• Ratcheting torque screwdriver with a Phillips head that exerts up to 15 pound-force inches (lbf-in.)
or 240 ounce-force inches (ozf-in.) of pressure
• Panduit crimping tool with optional controlled cycle mechanism (model CT-700, CT-720, CT-920,
CT-920CH, CT-930, or CT-940CH)
• 6-gauge copper ground wire (insulated or noninsulated)
• Four leads of 18-gauge copper wire
• Wire-stripping tools for stripping 6- and 18-gauge wires
Grounding the Switch
Warning
This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the
absence of a suitably installed ground conductor. Contact the appropriate electrical inspection
authority or an electrician if you are uncertain that suitable grounding is available.
Statement 1024
Caution To make sure that the equipment is reliably connected to earth ground, follow the grounding procedure
instructions, and use a UL-listed lug suitable for number-6 AWG wire and two number-10-32
ground-lug screws.
To ground the switch to earth ground, follow these steps. Make sure to follow any grounding
requirements at your site.
Step 1 Locate and remove the ground lug and the two number-10-32 ground-lug screws from the rear panel of
the switch. (See Figure C-3 for location.) Use a standard Phillips screwdriver or a ratcheting torque
screwdriver with a Phillips head. Set the screws and the ground lug aside.
Step 2 If your ground wire is insulated, use a wire stripping tool to strip the 6-gauge ground wire to 0.5
inch (12.7 mm) ± 0.02 inch (0.5 mm), as shown in Figure C-1.
- Catalyst 3560 Switch 1
- Hardware 1
- Installation Guide 1
- CONTENTS 3
- Contents 4
- 4 Troubleshooting 4-1 5
- Audience 7
- Conventions 7
- Related Publications 8
- OL-6337-07 10
- Product Overview 11
- Front Panel Description 13
- 10/100 and 10/100/1000 Ports 18
- PoE Ports 19
- SFP Module Slots 20
- Dual-Purpose Port 20
- System LED 21
- RPS LED 22
- Port LEDs and Modes 23
- Rear Panel Description 25
- Internal Power Supply 28
- Cisco RPS 29
- Console Port 29
- Management Options 30
- Network Configurations 31
- Warnings 34
- Installation Guidelines 37
- Verifying Switch Operation 38
- Installing the Switch 39
- Mounting the Switch in a Rack 42
- Attaching the Cable Guide 43
- Wall-Mounting 44
- Statement 265 45
- Mounting the Switch on a Wall 46
- Table- or Shelf- Mounting 47
- 10/100 or 10/100/1000 Ports 51
- Class 1 laser product 53
- Statement 1008 53
- Catalyst 3560 55
- Where to Go Next 56
- Equipment That You Supply 62
- Desk or Shelf Mounting 64
- Statement 378 68
- CABLE SIDE ENTRY 69
- THIS SIDE AWAY FROM 69
- MOUNTING SURFACE 69
- Magnet Mounting 71
- Rack-Mounting 72
- Securing the AC Power Cord 75
- Troubleshooting 77
- Evaluate Switch POST Results 78
- Monitor Switch LEDs 78
- Verify Switch Connections 78
- Ethernet and Fiber Cables 79
- Link Status 79
- Monitor Switch Performance 80
- Cabling Distance 81
- 126757, 781-00303-01A0 83
- 119952, 781-00290-01 83
- 250518, 781-00604-01 A0 83
- Technical Specifications 85
- Power over Ethernet 86
- Connector Specifications 93
- SFP Module Ports 94
- Dual-Purpose Ports 95
- Identifying a Crossover Cable 98
- Adapter Pinouts 99
- Signal DB-25 Pin Signal 100
- Connecting to DC Power 101
- Preparing for Installation 102
- Grounding the Switch 102
- Wire lead 103
- 0.5 in. (12.7 mm) 103
- 0.02 in. (0.5 mm) 103
- Insulation 103
- 1 Ground hole location 104
- Statement 1003 105
- Statement 1030 105
- Statement 122 106
- Preparing for Setup 109
- Completing the Setup Program 111
- Step 10 These choices appear: 113
- • CMS from your browser 113
- Numerics 115
- PoE shock hazard 2-4, 3-4 120
Related products and manuals for Computer Accessories Cisco 3560
Computer Accessories Cisco 1800 User Manual
(74 pages)
(74 pages)
Computer Accessories Cisco 15600 User Manual
(78 pages)
(78 pages)
Computer Accessories Cisco 3750 User Manual
(86 pages)
(86 pages)
Computer Accessories Cisco 4948 User Manual
(14 pages)
(14 pages)
Computer Accessories Cisco 12006 User Manual
(16 pages)
(16 pages)
Computer Accessories Cisco 6500 User Manual
(72 pages)
(72 pages)
© 2020, manymanuals.com. All rights reserved. | 0.075 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals