Cisco 3560 User Manual Page 37
- Page / 120
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
2-5
Catalyst 3560 Switch Hardware Installation Guide
OL-6337-07
Chapter 2 Switch Installation (24- and 48-Port Switches)
Preparing for Installation
Statement 371—Power Cable and AC Adapter
Caution To comply with the Telcordia GR-1089 Network Equipment Building Systems (NEBS) standard for
electromagnetic compatibility and safety, connect the ethernet cables only to intrabuilding or
nonexposed wiring or cabling.
Caution To comply with the Telcordia GR-1089 NEBS standard, PoE or non-PoE 10/100/1000 Ethernet port
cables that exit from either the left side or right side of the switch should be routed and tied to the nearest
rack metal hardware.
Note The grounding architecture of this product is DC-isolated (DC-I).
Installation Guidelines
When you determine where to place the switch, be sure to observe these requirements:
• The operating environment is within the ranges listed in Appendix A, “Technical Specifications.”
• Airflow around the switch and through the vents is unrestricted.
• Clearance to front and rear panels meets these conditions:
–
You can easily read the front-panel indicators.
–
Access to ports is sufficient for unrestricted cabling.
–
The rear-panel power connector is within reach of an AC power receptacle.
• Temperature around the unit does not exceed 113°F (45°C).
If the switch is installed in a closed or multirack assembly, the temperature around it might be
greater than normal room temperature.
• Cabling is away from sources of electrical noise, such as radios, power lines, and fluorescent
lighting fixtures. Make sure the cabling is safely away from other devices that might damage the
cables.
• For copper Ethernet ports, including 10/100 ports, 10/100/1000 ports, and 1000BASE-T SFP
module ports, cable lengths from the switch to connected devices can be up to 328 feet (100 meters).
• The cables meet the specifications in Table B-1 on page B-4, which lists the cable specifications for
1000BASE-X and 100BASE-X SFP modules for the Catalyst 3560 switch. Catalyst 3560 switch
SFP ports use both GLC-GE-100XX and GLC-FE-100XX SFP modules.
When you use shorter lengths of single-mode fiber cable, you might need to insert an inline optical
attenuator in the link to avoid overloading the receiver.
- Catalyst 3560 Switch 1
- Hardware 1
- Installation Guide 1
- CONTENTS 3
- Contents 4
- 4 Troubleshooting 4-1 5
- Audience 7
- Conventions 7
- Related Publications 8
- OL-6337-07 10
- Product Overview 11
- Front Panel Description 13
- 10/100 and 10/100/1000 Ports 18
- PoE Ports 19
- SFP Module Slots 20
- Dual-Purpose Port 20
- System LED 21
- RPS LED 22
- Port LEDs and Modes 23
- Rear Panel Description 25
- Internal Power Supply 28
- Cisco RPS 29
- Console Port 29
- Management Options 30
- Network Configurations 31
- Warnings 34
- Installation Guidelines 37
- Verifying Switch Operation 38
- Installing the Switch 39
- Mounting the Switch in a Rack 42
- Attaching the Cable Guide 43
- Wall-Mounting 44
- Statement 265 45
- Mounting the Switch on a Wall 46
- Table- or Shelf- Mounting 47
- 10/100 or 10/100/1000 Ports 51
- Class 1 laser product 53
- Statement 1008 53
- Catalyst 3560 55
- Where to Go Next 56
- Equipment That You Supply 62
- Desk or Shelf Mounting 64
- Statement 378 68
- CABLE SIDE ENTRY 69
- THIS SIDE AWAY FROM 69
- MOUNTING SURFACE 69
- Magnet Mounting 71
- Rack-Mounting 72
- Securing the AC Power Cord 75
- Troubleshooting 77
- Evaluate Switch POST Results 78
- Monitor Switch LEDs 78
- Verify Switch Connections 78
- Ethernet and Fiber Cables 79
- Link Status 79
- Monitor Switch Performance 80
- Cabling Distance 81
- 126757, 781-00303-01A0 83
- 119952, 781-00290-01 83
- 250518, 781-00604-01 A0 83
- Technical Specifications 85
- Power over Ethernet 86
- Connector Specifications 93
- SFP Module Ports 94
- Dual-Purpose Ports 95
- Identifying a Crossover Cable 98
- Adapter Pinouts 99
- Signal DB-25 Pin Signal 100
- Connecting to DC Power 101
- Preparing for Installation 102
- Grounding the Switch 102
- Wire lead 103
- 0.5 in. (12.7 mm) 103
- 0.02 in. (0.5 mm) 103
- Insulation 103
- 1 Ground hole location 104
- Statement 1003 105
- Statement 1030 105
- Statement 122 106
- Preparing for Setup 109
- Completing the Setup Program 111
- Step 10 These choices appear: 113
- • CMS from your browser 113
- Numerics 115
- PoE shock hazard 2-4, 3-4 120
Related products and manuals for Computer Accessories Cisco 3560
Computer Accessories Cisco 1800 User Manual
(74 pages)
(74 pages)
Computer Accessories Cisco 15600 User Manual
(78 pages)
(78 pages)
Computer Accessories Cisco 3750 User Manual
(86 pages)
(86 pages)
Computer Accessories Cisco 4948 User Manual
(14 pages)
(14 pages)
Computer Accessories Cisco 12006 User Manual
(16 pages)
(16 pages)
Computer Accessories Cisco 6500 User Manual
(72 pages)
(72 pages)
© 2020, manymanuals.com. All rights reserved. | 0.068 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals