Cisco 15327 User Manual Page 462
- Page / 584
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
26-30
Ethernet Card Software Feature and Configuration Guide, R7.2
Chapter 26 Configuring IEEE 802.17b Resilient Packet Ring
Configuring RPR-IEEE End-to-End
Advertised Protection requests:
ringlet0: IDLEringlet1: IDLE
Active Edges:
ringlet0: NO ringlet1: NO
Preferred protection mode: STEERING
Jumbo preference: NOT SET (ring doesn't supports JUMBOS)
Measured LRTT: 0
Sequence Number: 3
ATD INFO:
Station Name: ML100X-491
A0 reserved Bandwidth:
ringlet0: 0 mbpsringlet1: 0 mbps
SAS enabled: YES
Weight:
ringlet0: 1ringlet1: 1
Secondary Mac Addresses:
MAC 1: 0000.0000.0000 (UNUSED)
MAC 2: 0000.0000.0000 (UNUSED)
=======================================================================
Topology entry at Index 5 on ringlet 1:
Station MAC address: 0005.9a3c.59c0
Valid on ringlet1: YES
Entry reachable: YES
Advertised Protection requests:
ringlet0: IDLEringlet1: IDLE
Active Edges:
ringlet0: NO ringlet1: NO
Preferred protection mode: STEERING
Jumbo preference: NOT SET (ring doesn't supports JUMBOS)
Measured LRTT: 0
Sequence Number: 3
ATD INFO:
Station Name: ML100T-481
A0 reserved Bandwidth:
ringlet0: 0 mbpsringlet1: 0 mbps
SAS enabled: YES
Weight:
ringlet0: 1ringlet1: 1
Secondary Mac Addresses:
MAC 1: 0000.0000.0000 (UNUSED)
MAC 2: 0000.0000.0000 (UNUSED)
Configuring RPR-IEEE End-to-End
You need to use both CTC and Cisco IOS to configure RPR-IEEE for the ML-Series card. CTC is the
graphical user interface (GUI) that serves as the enhanced craft tool for specific ONS node operations,
including the provisioning of the point-to-point SONET/SDH circuits required for RPR-IEEE. Cisco
IOS is used to configure RPR-IEEE on the ML-Series card and its interfaces.
Successfully creating an RPR-IEEE requires these procedures:
•
Provisioning Card Mode, page 2-4 (CTC)
•
Connecting the ML-Series Cards with Point-to-Point STS/STM Circuits, page 26-31 (CTC or TL1)
•
Creating the RPR-IEEE Interface and Bridge Group, page 26-32 (Cisco IOS)
•
Verifying RPR-IEEE End-to-End Ethernet Connectivity, page 26-37 (Cisco IOS)
- Configuration Guide 1
- CONTENTS 3
- Contents 10
- About this Guide 27
- Document Objectives 28
- Audience 28
- Document Organization 29
- Related Documentation 30
- Document Conventions 31
- Waarschuwing 32
- Varoitus 32
- Attention 33
- Avvertenza 33
- Advarsel 33
- ¡Advertencia! 34
- Varning! 34
- ML-Series Card Overview 39
- ML-Series Feature List 40
- ML-Series Feature List 41
- CTC Operations 45
- Baseline 46
- Auto-Refresh 46
- Chapter 2 CTC Operations 47
- Managing SONET/SDH Alarms 48
- J1 Path Trace 49
- J1 Path Trace 50
- Initial Configuration 51
- Figure 3-1 CTC IOS Window 53
- Node IP address 54
- RJ-45 Cable 56
- RJ-11 to RJ-45 56
- Console Port Adapter Cable 56
- ML1000-2 CONSOLE Port 56
- Startup Configuration File 57
- Passwords 58
- Configuring the Hostname 59
- Multiple Microcode Images 61
- Cisco IOS Command Modes 63
- Using the Command Modes 65
- Getting Help 66
- Configuring Interfaces 67
- MAC Addresses 68
- Interface Port ID 68
- Basic Interface Configuration 69
- Configuration 70
- CRC Threshold Configuration 77
- Interfaces 78
- Configuring POS 81
- Chapter 5 Configuring POS 82
- SW-LCAS 83
- Setting the MTU Size 85
- SONET/SDH Alarms 86
- Configuring SONET/SDH Alarms 87
- C2 Byte and Scrambling 88
- Monitoring and Verifying POS 89
- POS Configuration Examples 91
- ML_Series_A 92
- Configuring Bridges 97
- Configuring Basic Bridging 98
- IP Routing Mode 101
- No IP Routing Mode 102
- Bridge CRB Mode 103
- Bridge IRB Mode 104
- Chapter 6 Configuring Bridges 106
- Bridge IRB Mode 106
- Configuring STP and RSTP 107
- STP Overview 108
- Supported STP Instances 108
- Bridge Protocol Data Units 108
- Election of the Root Switch 109
- Spanning-Tree Timers 110
- Blocking State 112
- Listening State 113
- Learning State 113
- Forwarding State 113
- Disabled State 113
- STP and IEEE 802.1Q Trunks 114
- Supported RSTP Instances 115
- Rapid Convergence 116
- Rapid Convergence 117
- Synchronization of Port Roles 118
- Table 7-4 RSTP BPDU Flags 119
- Topology Changes 120
- Disabling STP and RSTP 122
- Configuring the Root Switch 123
- Configuring the Port Priority 123
- Configuring the Path Cost 124
- Configuring the Hello Time 125
- Configuring VLANs 129
- ONS 15454 130
- Chapter 8 Configuring VLANs 134
- Protocol Tunneling 135
- IEEE 802.1Q Example 139
- Figure 9-3 ERMS Example 141
- Configuring Link Aggregation 149
- Configuring EtherChannel 150
- Configuring POS Channel 152
- ML_Series A 154
- ML_Series B 154
- Enabling IP Routing 161
- Configuring IP Routing 162
- Configuring RIP 163
- RIP Authentication 165
- Configuring OSPF 167
- Configuring OSPF 168
- OSPF Interface Parameters 171
- OSPF Area Parameters 172
- Change LSA Group Pacing 176
- Loopback Interface 177
- Monitoring OSPF 177
- Configuring EIGRP 178
- Configuring EIGRP 179
- EIGRP Router Mode Commands 180
- EIGRP Interface Mode Commands 181
- Configuring BGP 185
- Table 11-6 BGP Show Commands 186
- Configuring IS-IS 187
- Configuring Static Routes 189
- Monitoring Static Routes 190
- Configuring IRB 195
- IRB Configuration Example 197
- Monitoring and Verifying IRB 198
- Configuring VRF Lite 201
- vrf-name 207
- Understanding QoS 209
- Ethernet CoS 211
- ML-Series QoS 212
- Policing 213
- Scheduling 214
- Scheduling 215
- Egress Priority Marking 216
- Ingress Priority Marking 216
- Flow Control Pause and QoS 217
- QoS on Cisco Proprietary RPR 218
- Configuring QoS 220
- Creating a Traffic Policy 221
- Configuring CoS-Based QoS 225
- QoS Configuration Examples 226
- ML-Series VoIP Example 229
- ML-Series Policing Example 229
- Router_a 230
- Default Multicast QoS 232
- QoS not Configured on Egress 235
- Understanding IP SLA 239
- IP SLA on the ML-Series 240
- Understanding the SDM 243
- Understanding SDM Regions 243
- Configuring SDM 244
- Monitoring and Verifying SDM 245
- Monitoring and Verifying SDM 246
- Understanding ACLs 247
- ML-Series ACL Support 247
- Named IP ACLs 248
- User Guidelines 248
- Creating IP ACLs 249
- Modifying ACL TCAM Size 251
- Modifying ACL TCAM Size 252
- Role of SONET/SDH Circuits 254
- Packet Handling Operations 254
- Ring Wrapping 255
- Fiber Cut 256
- ML-Series RPR 256
- Ring Wrap 256
- MAC Address and VLAN Support 258
- Cisco Proprietary RPR QoS 259
- ML-Series Card 264
- Access Ports 270
- Router(config-if)# shutdown 278
- LFP Sequence 281
- Configuring LFP 282
- Monitoring and Verifying LFP 283
- Balancing 288
- Understanding EoMPLS 293
- Understanding EoMPLS 294
- EoMPLS Support 295
- EoMPLS Restrictions 295
- EoMPLS Quality of Service 295
- Configuring EoMPLS 296
- ip-address 297
- bridge-group-number 300
- EoMPLS Configuration Example 301
- VC Type 5 302
- Understanding MPLS-TE 305
- Configuring MPLS-TE 306
- Configuring an MPLS-TE Tunnel 307
- MPLS-TE Configuration Example 308
- RPRW Alarm 311
- RPRW Alarm 312
- Understanding Security 313
- Understanding SSH 314
- Configuring SSH 315
- Configuring the SSH Server 316
- RADIUS on the ML-Series Card 318
- RADIUS Relay Mode 318
- RADIUS Stand Alone Mode 319
- Understanding RADIUS 320
- Configuring RADIUS 320
- Default RADIUS Configuration 321
- Defining AAA Server Groups 325
- Starting RADIUS Accounting 328
- POS on ONS Ethernet Cards 333
- POS Interoperability 334
- Encapsulation Type and CRC 335
- POS Encapsulation Types 336
- Figure 20-2 RPR Data Frames 337
- Cisco HDLC 338
- POS Framing Modes 339
- Configuring RMON 345
- Chapter 21 Configuring RMON 347
- Clearing of CRC-ALARM 351
- Unwrap Synchronization 352
- Unwrap Synchronization 353
- Bidirectional Errors 354
- User issues 356
- Displaying RMON Status 364
- Displaying RMON Status 366
- Configuring SNMP 367
- SNMP on the ML-Series Card 368
- SNMP Versions 369
- SNMP Manager Functions 369
- SNMP Agent Functions 370
- SNMP Community Strings 370
- Supported MIBs 371
- SNMP Notifications 371
- Disabling the SNMP Agent 373
- Configuring Community Strings 373
- Chapter 22 Configuring SNMP 374
- SNMP Examples 379
- Displaying SNMP Status 380
- G-Series Application 381
- G1K-4 and G1000-4 Comparison 382
- G-Series Example 383
- ONS Node 385
- Point-to-Point Circuit 387
- ONS Node ONS Node 387
- ONS NodeONS Node 388
- SONET/SDH 388
- Ethernet 388
- Ethernet TDM 389
- Gigabit Ethernet Ports 391
- E-Series Application 393
- E-Series Modes 394
- Port-Mapped (Linear Mapper) 395
- E-Series VLAN Support 397
- Data Flow 399
- Redundant path (blocked) 401
- Primary path (forwarding) 401
- E-Series Circuit Protection 404
- CE-100T-8 Ethernet Operation 409
- CE-100T-8 Ethernet Features 410
- Figure 24-2 Flow Control 411
- RMON and SNMP Support 414
- Statistics and Counters 414
- CE-100T-8 Pools 419
- CE-100T-8 Pools 420
- Both Port 6 and Port 7 421
- CE-1000-4 Ethernet Operation 425
- CE-1000-4 Ethernet Features 426
- Flow Control 427
- Understanding RPR-IEEE 433
- Advantages of RPR-IEEE 434
- RPR-IEEE Framing Process 435
- RPR-IEEE Framing Process 436
- CTM and RPR-IEEE 438
- Configuring Jumbo Frames 442
- Configuring Protection Timers 444
- Configuring a Span Shutdown 446
- Configuring Keepalive Events 446
- Configuring QoS on RPR-IEEE 449
- Configuring Fairness Weights 451
- is populated only by the 458
- Provisioning Card Mode 463
- RI Configuration Example 471
- RI Configuration Example 474
- Command Reference 475
- Appendix A Command Reference 476
- Router(config)# 476
- [no] clock auto 477
- interface spr 1 478
- microcode fail system-reload 480
- [no] pos pdi holdoff time 481
- [no] pos report alarm 482
- [no] pos scramble-spe 484
- [no] rpr-ieee ri foreign 487
- Maintenance) 490
- rpr-ieee flag c2 value 496
- [no] rpr-ieee report alarm 498
- Related Commands show int pos 519
- show ons alarm 521
- Related Commands None 551
- [no] shutdown 552
- At the PE1 interface: 558
- At the PE2 interface: 558
- Unsupported CLI Commands 559
- Commands 562
- Configuration Commands 563
- Using Technical Support 567
- Numerics 571
Related products and manuals for Hardware Cisco 15327
Hardware Cisco 10720 User Manual
(26 pages)
(26 pages)
Hardware Cisco 10700 User Manual
(16 pages)
(16 pages)
Hardware Cisco XR 12000 Series User Manual
(148 pages)
(148 pages)
Hardware Cisco 15310-MA User Manual
(10 pages)
(10 pages)
Hardware Cisco 7100 Series User Manual
(24 pages)
(24 pages)
Hardware Cisco 12012 User Manual
(34 pages)
(34 pages)
Hardware Cisco 2600 User Manual
(32 pages)
(32 pages)
Hardware Cisco 3725 User Manual
(22 pages)
(22 pages)
Hardware Cisco WRT320N User Manual
(53 pages)
(53 pages)
Hardware Cisco 7200 VXR User Manual
(64 pages)
(64 pages)
Hardware Cisco 1600 User Manual
(13 pages)
(13 pages)
Hardware Cisco 12406 User Manual
(36 pages)
(36 pages)
Hardware Cisco WES610N User Manual
(546 pages)
(546 pages)
Hardware Cisco 3500 Series User Manual
(8 pages)
(8 pages)
Hardware Cisco 1005 User Manual
(6 pages)
(6 pages)
Hardware Cisco 2600 Series User Manual
(10 pages)
(10 pages)
Hardware Cisco 1720 User Manual
(12 pages)
(12 pages)
Hardware Cisco 3660 User Manual
(10 pages)
(10 pages)
Hardware Cisco 32369 User Manual
(52 pages)
(52 pages)
© 2020, manymanuals.com. All rights reserved. | 0.881 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals