Cisco C8510-SRP - Switch Route Processor Troubleshooting Guide Page 426

  • Download
  • Add to my manuals
  • Print
  • Page
    / 502
  • Table of contents
  • TROUBLESHOOTING
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 425
13-22
ATM and Layer 3 Switch Router Troubleshooting Guide
OL-1969-01
Chapter 13 Troubleshooting ATM Router Module Connections
Troubleshooting RFC 1483 on ATM Router Module Connections
Step 2 Use the show running-config command to confirm your configuration.
Switch# show running-config
Building configuration...
Current configuration:
.
(Information Deleted)
.
!
atm connection-traffic-table-row index 110 ubr pcr 1
.
(Information Deleted)
.
interface ATM10/0/1.3 multipoint
ip address 2.2.0.2 255.255.255.0
map-group RFC1483_2
atm pvc 2 109 pd on rx-cttr 110 tx-cttr 110 interface ATM0/0/0 0 109 upc drop
!
.
(Information Deleted)
.
map-list RFC1483_2
ip 2.2.0.1 atm-vc 109 broadcast
ip 11.1.10.1 atm-vc 110 broadcast
Step 3 Use the show interfaces atm command to confirm the configuration of the ingress ATM interface
connected to the Cisco 7500 router.
Switch# show interfaces atm 0/0/0
ATM0/0/0 is up, line protocol up
Hardware is quad_oc12suni
Internet address is 10.0.1.26/30
MTU 4470 bytes, sub MTU 4470, BW 622080 Kbit, DLY 0 usec,
rely 255/255, load 1/255
Encapsulation ATM, loopback set, keepalive not supported
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Queueing strategy: fifo
Output queue 0/40, 0 drops; input queue 0/75, 0 drops
5 minute input rate 4000 bits/sec, 9 packets/sec
5 minute output rate 4000 bits/sec, 9 packets/sec
16300 packets input, 863900 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
16808 packets output, 890824 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 output buffer failures, 0 output buffers swapped out
Step 4 Confirm the interface and protocol are both up.
Step 5 Use the show interfaces atm command to confirm the configuration of the ATM router module
interface.
Switch# show interfaces atm 10/0/1
ATM10/0/1 is up, line protocol is up
Hardware is ATM router module_port, address is 0090.2141.bc58 (bia 0090.2141.bc58)
SVC idle disconnect time: 300 seconds
MTU 1500 bytes, sub MTU 1500, BW 1000000 Kbit, DLY 10 usec,
rely 255/255, load 1/255
Encapsulation ATM, loopback not set, keepalive not supported
Full-duplex, 1000Mb/s, 100BaseFX
ARP type: ARPA, ARP Timeout 00:15:00
Last input 00:02:13, output never, output hang never
Last clearing of "show interface" counters never
Page view 425
1 ... 425 426 427 ... 502

Comments to this Manuals

No comments