Cisco C8510-SRP - Switch Route Processor Troubleshooting Guide Page 460
- Page / 502
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
(DRAFT LABEL) FINAL DRAFT - CISCO CONFIDENTIAL 2/13/02
B-6
ATM and Layer 3 Switch Router Troubleshooting Guide
OL-1969-01
Appendix Troubleshooting TACACS+ and Recovering Passwords
Recovering a Lost Password
All of the procedures for recovering lost passwords depend on changing the configuration register of the
switch router. This is done by reconfiguring the switch router software.
More recent Cisco platforms run from Flash memory or are netbooted from a network server and can
ignore the contents of nonvolatile random-access memory (NVRAM) when booting. By ignoring the
contents of NVRAM, you can bypass the configuration file (which contains the passwords) and gain
complete access to the switch router. You can then recover the lost password or configure a new one.
Note If your password is encrypted, you cannot recover it. You must configure a new password.
Follow these steps to recover a password:
Step 1 Beginning in the privileged executive mode, enter the show version command and the configuration
register value. The default value is 0x2102.
Step 2 Power cycle the switch router.
Step 3 Within 60 seconds of turning the switch router On, press the Break key sequence or send a break signal,
which is usually ^]. If you do not see the
> prompt with no switch router name, the terminal is not
sending the correct Break signal. In that case, check the terminal or terminal emulation setup.
Step 4 Enter the confreg command at the > prompt.
Step 5 Answer yes to the Do you wish to change configuration [y/n]? prompt.
Step 6 Answer no to all the questions that appear until you reach the Ignore system config info [y/n] prompt.
Answer yes.
Step 7 Answer no to the remaining questions until you reach the Change boot characteristics [y/n]? prompt.
Answer yes.
Step 8 At the enter to boot: prompt, enter 2.
Step 9 Answer no to the Do you wish to change configuration [y/n]? prompt.
Step 10 Enter the reset command at the rommon> prompt.
Step 11 Enter the enable command at the Switch> prompt. You'll be in enable mode and see the Switch# prompt.
Step 12 Enter the show startup-config command to view your password.
Step 13 If your password is clear text, proceed to Step 16.
or
If your password is encrypted, continue with Step 14.
Step 14 If your password is encrypted, enter the configure memory command to copy the NVRAM into
memory.
Step 15 Enter the copy running-config startup-config command.
Step 16 Enter the configure terminal command.
Step 17 Enter the enable secret password command.
Step 18 Enter the config-register value command, where value is whatever value you entered in Step 1.
Step 19 Enter the exit command to exit configuration mode.
Step 20 Enter the copy running-config startup-config command.
Step 21 Enter the reload command at the prompt.
- Cisco Reader Comment Card 1
- BUSINESS REPLY MAIL 2
- Troubleshooting Guide 3
- CONTENTS 5
- 3 Initial Troubleshooting 3-1 6
- 4 Example Network 4-1 6
- Contents 10
- OL-1969-01 10
- C ATM Cell Structures C-1 15
- D Creating a Core Dump D-1 15
- F Technical Support F-1 15
- Audience 17
- Organization 18
- Related Documentation 19
- Conventions 20
- Obtaining Documentation 21
- Cisco.com 22
- Technical Assistance Center 22
- Contacting TAC by Telephone 23
- Troubleshooting Overview 25
- Troubleshooting Tools 29
- Converted show epc Commands 30
- Using Diagnostic Commands 31
- • TDRs and OTDRs, page 2-5 32
- • Network Monitors, page 2-5 32
- • Network Analyzers, page 2-6 32
- TDRs and OTDRs 33
- Network Monitors 33
- Network Analyzers 34
- Initial Troubleshooting 35
- Accessibility Test 36
- OIR Test 36
- Snake Test 36
- Examples 37
- Using Bug Toolkit 39
- Checking IOS Release Notes 41
- Finding the Image 45
- IOS Upgrade Procedures 46
- Maintaining Functional Images 46
- Catalyst 8540 MSR) 48
- Example Network 55
- Example Networks 56
- Physical Connections 57
- Virtual Connections 58
- Chapter 4 Example Network 59
- Interface Connections 73
- Checking Cell Rates 75
- Performing OAM Loopback Tests 78
- OAM Loopback Testing 81
- Configuring Loopback Examples 82
- Line Coding Errors 89
- Interface Module LEDs 98
- OL-1969-02 103
- Port Adapter LEDs 104
- Interfaces 125
- • An AIS defect 131
- Network Connections 133
- Checking the UBR Resources 138
- • Packet discard 145
- • UPC option 145
- Checking UNI Interfaces 150
- Debugging SVC Signalling 153
- Alternate SVC Diagnostics 154
- Debugging PNNI SVC Routing 156
- Checking ATM Routes 157
- Checking PNNI Topology 158
- Checking SVC Downstream 159
- Hierarchical Network 160
- Checking SVCC-RCC Status 176
- Checking SVCC-RCC Hello State 177
- Checking Link Aggregation 183
- • Debugging Summary Addresses 184
- Debugging Summary Addresses 186
- Checking Traffic Priority 193
- Using PNNI Trace Connection 196
- Initiating a Trace Connection 197
- Environments 203
- Debugging the LANE Connection 211
- Troubleshooting Tag and MPLS 213
- Switching Connections 213
- How Tag Switching Works 214
- Troubleshooting TDP Neighbors 220
- MPLS Overview 224
- How MPLS Works 225
- MPLS Example 229
- Verifying CEF Switching 232
- Verifying MPLS 235
- Pinging Neighbors 236
- Verifying Label Distribution 236
- Verifying Label Bindings 237
- Troubleshooting MPLS VPN 238
- Verifying VRF Configurations 239
- Verifying Routing Information 240
- Verifying Labels 242
- Pinging ATM VPN Connections 254
- Debugging MPLS 256
- Network Clocking 257
- Performing Basic Checks 258
- CES Example Network 260
- Overview of Network Clocking 263
- Network Clock Module LEDs 264
- Layer 3 to Layer 3 269
- Connection Troubleshooting 269
- Uplink Interfaces 271
- • Detect port stuck failure 276
- 100BASE-FX Interface Modules 279
- Interface Modules 303
- Module LED Descriptions 304
- • SONET Tech Tips 311
- Descriptions 311
- Descriptions (continued) 312
- Defining Layer 3 Switching 320
- Understanding Packet Flow 320
- C8540CSR-1 321
- C8540CSR-2 321
- Layer 3 Forwarding 324
- Layer 2 Bridging 324
- Overview of Layer 3 Switching 325
- System Architecture 326
- Route Processor 327
- Routing Protocols 328
- Layer 2 VLAN and Switching 328
- Cisco Express Forwarding 329
- CEF Operation 330
- The Frame Scheduler 332
- Line Card Architecture 334
- CEFA Search Engine 335
- Fabric Interface 335
- Figure 11-13 Shared CAM 337
- Checking the IP Routing Table 345
- Checking the Interface Status 346
- CAM encoding: 354
- 0x009021DDDDDD 354
- • IP routing is on 355
- Layer 3 IP Multicast Overview 361
- Dense Mode 362
- Sparse Mode 362
- The Multicast Routing Table 364
- Utilization Problems 369
- Troubleshooting SDM Problems 374
- Layer 2 Switching 383
- Bridging 384
- Layer 2 Switching Broadcasts 385
- Layer 2 CAM Display 393
- Check for Spanning Tree Loop 393
- Before Configuring IRB 395
- • Load balancing 398
- • Fault tolerance 398
- Layer 3 to ATM 403
- Connections 405
- ATM Router Module Overview 406
- Hardware Restrictions 407
- ATM Router Module Software 408
- IPX Switching Overview 422
- • That the IP routing is on 436
- Appendixes 443
- Debugging a Switch Router 445
- Using the Debug Interface 446
- Using the debug ? Command 447
- Enabling Message Logging 450
- Passwords 455
- Cannot Compile Daemon 456
- Daemon Is Not Up and Running 457
- Daemon Does Not Run 457
- Recovering a Lost Password 459
- ATM Cell Structures 461
- Appendix 462
- OAM Cell Structure 463
- LANE Data Frame 465
- Creating a Core Dump 467
- Using the write core Command 469
- APPENDIX 471
- Line Coding 472
- Connection Alarm Types 473
- Architecture Problems 474
- Port Stuck Message 477
- Potential Causes 478
- Technical Support 481
- Numerics 485
Related products and manuals for Networking Cisco C8510-SRP - Switch Route Processor
Networking Cisco 4430 User Manual
(12 pages)
(12 pages)
Networking Cisco SCE 2000 4/8xFE User Manual
(28 pages)
(28 pages)
Networking Cisco 2620XM User Manual
(6 pages)
(6 pages)
Networking Cisco EPC2203 User Manual
(10 pages)
(10 pages)
Networking Cisco Catalyst 4224 Specifications
(310 pages)
(310 pages)
Networking Cisco RV180 Setup Guide
(15 pages)
(15 pages)
Networking Cisco 7505 User Manual
(16 pages)
(16 pages)
Networking Cisco 1710 Technical Information
(26 pages)
(26 pages)
Networking Cisco MC16E Specifications
(19 pages)
(19 pages)
Networking Cisco WMA11B User's Guide
(2 pages)
(2 pages)
Yamaha AR-100 manuali
Manuali dei proprietari e guide per l'utente per Strumenti musicalo Yamaha AR-100.
We fornisce 2 manuali pdf Yamaha AR-100 per scaricare gratuitamente in base al tipo di documento: Specifiche, Manuale Utente
Comments to this Manuals