Cisco 1700 Series Specifications Page 16
- Page / 258
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Preface
Organization
xiv
Cisco 1700 Series Router Software Configuration Guide
78-5407-03
Organization
This document contains the following chapters and appendixes:
• Chapter 1, “Introduction to Router Configuration”—Describes what you
need to know about the Cisco IOS software (the software that runs the router)
before you begin to configure the router.
• Chapter 2, “Configuring Security Features”—Describes how to configure
security features on Cisco routers, including IP Security (IPSec), firewalls,
and virtual private dial-up networks (VPDNs).
• Chapter 3, “Miscellaneous Features”—Provides procedures for configuring
miscellaneous features of the Cisco 1700 Series routers: Dynamic Host
Configuration Protocol (DHCP) and Network Address Translation (NAT).
• Chapter 4, “Configuring Routing Among VLANs with IEEE 802.1Q
Encapsulation”—Describes the required and optional tasks for configuring
routing between VLANs with IEEE 802.1Q encapsulation.
• Chapter 5, “Configuring ISDN”—Describes how to configure a Cisco router
to dial into a central-site router over an Integrated Services Digital Network
(ISDN) line.
• Chapter 6, “Configuring a Leased Line”—Describes how to configure a
Cisco router for Internet Protocol (IP) and Internetwork Packet Exchange
(IPX) over a private synchronous serial line.
• Chapter 7, “Configuring Frame Relay”—Describes how to configure a Cisco
router to connect to a central-site router over a Frame Relay line.
• Chapter 8, “Configuring Asynchronous Connections”—Describes how to
configure a Cisco router to dial into a central-site router over a standard
telephone line.
• Chapter 9, “Configuring X.25”—Describes how to configure a Cisco router
to connect to a central-site router over an X.25 line.
• Appendix A, “Networking Concepts”—Describes concepts that can help you
in designing your network and configuring your router according to the
examples in this guide.
• Appendix B, “ROM Monitor”—Describes the functions and commands of
the router ROM monitor (also called the bootstrap program), the firmware
that runs when the router is powered up or reset.
- Cisco Reader Comment Card 1
- General Information 1
- Document Information 1
- Mailing Information 1
- BUSINESS REPLY MAIL 2
- Configuration Guide 3
- CONTENTS 5
- 3 Miscellaneous Features 3-1 6
- 5 Configuring ISDN 5-1 7
- 7 Configuring Frame Relay 7-1 9
- Contents 10
- 78-5407-03 10
- 9 Configuring X.25 9-1 11
- A Networking Concepts A-1 12
- B ROM Monitor B-1 12
- Objectives 15
- Audience 15
- Organization 16
- Conventions 17
- Related Documentation 18
- Obtaining Documentation 18
- Ordering Documentation 19
- Documentation Feedback 19
- Cisco.com 20
- Technical Assistance Center 20
- Cisco TAC Web Site 21
- Cisco TAC Escalation Center 22
- Understanding Command Modes 24
- Getting Help 28
- Entering Configuration Mode 30
- Using Commands 31
- Saving Configuration Changes 32
- Using Debug Commands 33
- Where to Go Next 34
- Configuring Security Features 35
- Configuring IP Security 36
- Disabling Hardware Encryption 37
- Configuring Firewalls 39
- Configuration Examples 41
- Inspection Rules 42
- Miscellaneous Features 43
- Configuration Example 44
- • VLAN Commands 49
- Enabling IP Routing 50
- Enabling NetWare Routing 52
- Configuration 53
- VLAN Commands 54
- Usage Guidelines 56
- Syntax Description 56
- Command Mode 56
- Configuring ISDN 59
- Router# ping 192.168.37.40 73
- Troubleshooting 74
- Configuring IPX Routing 91
- Clearing the ISDN Interface 93
- Dial-In ISDN BRI Pool 100
- Configuring EIGRP Routing 103
- Command Task 105
- Configuring a Leased Line 107
- Before You Begin 108
- Configuring Global Parameters 109
- Configuring Security 109
- Verifying Your Configuration 112
- Configuring Frame Relay 117
- Frame Relay 118
- • debug ppp authentication 145
- • debug ppp multilink events 145
- Configuring Routing Protocols 155
- Floating Static Routes 156
- Assumptions 157
- Configuring Asynchronous 169
- Connections 169
- Asynchronous Dial-In Pool 180
- Configuring X.25 187
- X.25 over ISDN B Channel 196
- X.25 over ISDN D Channel 206
- Troubleshooting X.25 Problems 216
- Networking Concepts 217
- ISDN Components 218
- Services 219
- Sample Configuration 219
- WAN Technologies 221
- CHAP and PAP Authentication 223
- Access Lists 224
- Dialer Pools 225
- Network Address Translation 226
- Virtual LANs 227
- VLAN Issues 228
- Communicating Between VLANs 229
- Designing Switched VLANs 230
- ROM Monitor 233
- ROM Monitor Commands 235
- Command Descriptions 236
- Table 0-2 Boot Commands 237
- Required Variables 238
- Optional Variables 238
- Chapter B ROM Monitor 239
- Configuration Register 240
- Console Download 242
- Error Reporting 243
- Debug Commands 244
Related products and manuals for Networking Cisco 1700 Series
Networking Cisco SB 107 User's Guide
(155 pages)
(155 pages)
Networking Cisco SG 300-28P User Manual
(13 pages)
(13 pages)
Networking Cisco 4451-X Service Manual
(34 pages)
(34 pages)
Networking Cisco 1105 User Manual
(16 pages)
(16 pages)
Networking Cisco SGE2000 Specifications
(50 pages)
(50 pages)
Networking Cisco SRW224 User Manual
(5 pages)
(5 pages)
Networking Cisco OL-4015-08 Specifications
(212 pages)
(212 pages)
Networking Cisco 3640A User Manual
(8 pages)
(8 pages)
© 2020, manymanuals.com. All rights reserved. | 1.003 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals