Cisco 15216 EDFA2 Specifications Page 37
- Page / 112
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
3-11
Cisco ONS 15216 EDFA2 Operations Guide
78-13908-02
Chapter 3 Installation
Communications
An RS-232 link to the ONS 15216 EDFA2 is established. The user can now provision the ONS 15216
EDFA2. For provisioning instructions, see Chapter 4, “Provisioning.”
Remote Communication Setup
This section describes the procedure for establishing a remote dial-up connection to the ONS 15216
EDFA2. ONS 15216 EDFA2 remote communication requires two US Robotics 56K Fax modems set up
to send data over a two-wire dial-up telephone line. (See Figure 3-7.)
This section assumes the use of the US Robotics 56K Fax modem V.90. Other modem types may require
different settings to establish a remote dial-up connection. The user should review their modem
documentation to ensure compatibility between US Robotics and other vendor modem types.
Figure 3-7 Remote Communication
Remote Communication Component Requirements
Table 3-6 lists the components required to communicate remotely with a ONS 15216 EDFA2. Table 3-6
is divided into two sections: Remote Site and Local Site. The Remote Site section lists components
needed at the site that contains the ONS 15216 EDFA2 and the Local Site section lists components
needed at the site where the user is located.
Table 3-5 User Levels and Passwords
User Level Password Description
monitor ro Can only display a few status parameters.
operator rw Performs the day-to-day operations on the equipment.
CISCO15 by default, there is no
password (press Enter)
Administrator who is responsible for configuring the ONS
15216 EDFA2 and performing software upgrades.
root root Super user who operates special commands that are reserved
for people who know the architecture of the ONS 15216
EDFA2.
Modem
Workstation
Modem
PSTN Dial up
Phone line
71458
Network
Cisco ONS 15216
EDFA2
Table 3-6 ONS 15216 EDFA2 Communication Components
Component Notes
Remote Site
1 ONS 15216 EDFA2
- Cisco ONS 15216 EDFA2 1
- Operations Guide 1
- CONTENTS 3
- 4 Provisioning 4-1 4
- Contents 5
- 6 CLI Commands 6-1 6
- 7 FTP Command Line 7-1 8
- 78-13908-02 10
- Obtaining Documentation 13
- Documentation Feedback 14
- Cisco.com 14
- Technical Assistance Center 14
- Contacting TAC by Telephone 15
- Applications 17
- Chapter 1 Applications 18
- Key Features 19
- Transient Suppression 20
- Low Noise 20
- SNMP MIBs 20
- Technical Specifications 21
- Maximum Input Power 22
- Electrical Specifications 23
- Mechanical Specifications 24
- External Features 24
- Front Panel 25
- Installation 27
- Communications 28
- Alarm Relay Contacts (RJ-45) 29
- Alarm Connection Procedure 29
- POWER LED (Green) 30
- FAIL LED (Red) 30
- SC/UPC Optical Ports 31
- Optical Connection Procedure 32
- Required Equipment 33
- RS-232 Connection Procedure 33
- Chapter 3 Installation 34
- Example 3-2 Login Response 36
- Remote Communication Setup 37
- Modem Signals 38
- Modem Power Up 38
- Configuration Settings 39
- GND RXD TXD 40
- Telnet Session 41
- Command Description 42
- Provisioning 43
- Set the IP Address Procedure 44
- Step 1 Click Start> Run 45
- Set Gain 46
- Set Alarm Thresholds 46
- CISCO ONS 15216 47
- ALARM OUT 47
- Chapter 4 Provisioning 48
- °C. Valid entries are 50
- °C. Valid 52
- °C. Setting this value to 0 52
- Set Password 53
- Save Changes 53
- SNMP Overview 55
- SNMP Agent 56
- SNMP MIBs and Message Types 57
- • Creating a View, page 5-6 59
- Creating a View 60
- Creating a Community Entry 61
- Display CommunityEntry 62
- Tables and Groups 63
- Setting Up Traps 70
- Trap Display Command 71
- Trap Set Command 71
- Retrieving Information 72
- Date and Time 73
- Power Gain 74
- Case Temperature 75
- Temperature Alarm Threshold 75
- CtmpMaxHysteresis 76
- CtmpMinHysteresis 76
- Power BUS Mode 77
- InPowerdBm 78
- LOSThreshold 78
- OutPoweruW 79
- OutPowerdBm 79
- LpoutSetpoint 79
- LpoutDeviation 80
- LpoutHysteresis 81
- AlarmEntry 81
- CLI Commands 83
- Chapter 6 CLI Commands 84
- Configuration Commands 85
- Administrative Commands 89
- Shell Commands 90
- FFS Commands 91
- SNMP Commands 92
- User Commands 102
- Restore Commands 106
- Manufacturer Mode 106
- FTP Command Line 107
- FTP Commands 108
Related products and manuals for Networking Cisco 15216 EDFA2
Networking Cisco SR224T User Manual
(4 pages)
Networking Cisco WGA11B User's Guide
(14 pages)
(14 pages)
Networking Cisco 1905/K9 User Manual
(2 pages)
(2 pages)
Networking Cisco SF100D-05 User Manual
(2 pages)
(2 pages)
Networking Cisco 675E User Manual
(12 pages)
(12 pages)
Networking Cisco MWR-1900-27 Specifications
(80 pages)
(80 pages)
Networking Cisco Engine 611 User Manual
(5 pages)
(5 pages)
Networking Cisco DPC2203 User Manual
(16 pages)
(16 pages)
Networking Cisco WUSB54GSC User's Guide
(59 pages)
(59 pages)
Networking Cisco CTX2500 Specifications
(10 pages)
(10 pages)
Networking Cisco X1000 User Manual
(26 pages)
(26 pages)
Networking Cisco EF3116 User Manual
(2 pages)
(2 pages)
© 2020, manymanuals.com. All rights reserved. | 0.118 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals