Cisco AS5800 Specifications Page 102
- Page / 334
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
3-20
Cisco AS5800 Operations, Administration, Maintenance, and Provisioning Guide
DOC-7810814=
Chapter 3 Operations
Verifying Modem Performance
Modem type is unknown.
Session limit is not set.
Time since activation: 00:12:24
Editing is enabled.
History is enabled, history size is 10.
DNS resolution in show commands is enabled
Full user help is disabled
Allowed transports are lat pad v120 telnet rlogin dsipcon. Preferred is lat.
No output characters are padded
No special data dispatching characters
Step 8 Program the display window so it does not pause in the middle of a screen display:
5800-NAS> terminal length 0
Step 9 Generate traffic across the modem link. Perform a lightweight stress test between the modems to
generate meaningful modem-performance statistics.
5800-NAS> show modem log
Modem 1/2/00 Events Log:
3w4d :Startup event:MICA Hex modem (Managed)
Modem firmware = 2.7.1.0
3w4d :RS232 event: noRTS, noDTR, CTS, noDCD
3w4d :RS232 event: noRTS, DTR, CTS, noDCD
The output generated by the show modem log command sends a large data stream across the modem
link - about 1 MB of data. The data should scroll freely for one or two minutes.
Step 10 Inspect the NAS modem that answered the call, and verify that it has acceptable connect speed,
throughput, and line shape. This example examines MICA modem 1/0. If you have Microcom modems,
enter the modem at-mode slot/port command followed by the at@e1 command.
5800-NAS> show modem operational-status 1/2/00
Modem(1/2/00) Operational-Status:
Parameter #0 Disconnect Reason Info: (0x0)
Type (=0 ): <unknown>
Class (=0 ): Other
Reason (=0 ): no disconnect has yet occurred
Parameter #1 Connect Protocol: LAP-M
Parameter #2 Compression: None
Parameter #3 EC Retransmission Count: 2
Parameter #4 Self Test Error Count: 0
Parameter #5 Call Timer: 118 secs
Parameter #6 Total Retrains: 0
Parameter #7 Sq Value: 3
Parameter #8 Connected Standard: V.90
Parameter #9 TX,RX Bit Rate: 48000, 28800
Parameter #11 TX,RX Symbol Rate: 8000, 3200
Parameter #13 TX,RX Carrier Frequency: 0, 1920
Parameter #15 TX,RX Trellis Coding: 0, 16
Parameter #16 TX,RX Preemphasis Index: 0, 6
Parameter #17 TX,RX Constellation Shaping: Off, Off
Parameter #18 TX,RX Nonlinear Encoding: Off, Off
Parameter #19 TX,RX Precoding: Off, Off
Parameter #20 TX,RX Xmit Level Reduction: 0, 0 dBm
Parameter #21 Signal Noise Ratio: 36 dB
Parameter #22 Receive Level: -19 dBm
Parameter #23 Frequency Offset: 0 Hz
Parameter #24 Phase Jitter Frequency: 0 Hz
Parameter #25 Phase Jitter Level: 0 degrees
- Cisco AS5800 Operations 1
- Provisioning Guide 1
- CONTENTS 3
- 2 Commissioning 2-1 4
- 3 Operations 3-1 5
- 4 Administration 4-1 5
- 5 Maintenance 5-1 6
- 6 Provisioning 6-1 6
- Contents 7
- Document Objectives 9
- Audience 9
- Document Organization 10
- Document Conventions 10
- Safety Warnings 11
- Related Documentation 12
- For More Information 14
- Obtaining Documentation 14
- Ordering Documentation 15
- Documentation Feedback 15
- Cisco.com 15
- Technical Assistance Center 16
- Introduction 19
- Chapter1 Introduction 20
- Cisco AS5800 Hardware Review 21
- System Architecture 22
- ROM Monitor 22
- Chapter 1 Introduction 23
- IP Subnetting Plan 24
- Device Parameters 25
- User Interface Command Modes 26
- Command Modes 27
- Context-Sensitive Help 28
- Basic Cisco AS5800 Start Up 29
- Cisco AS5800 First-Time Boot 33
- Using the Setup Script 34
- Passwords 35
- Commissioning 43
- Chapter 2 Commissioning 44
- Call-Processing Components 45
- Task 1. Verifying Basic Setup 47
- Inspecting the Dial Shelf 51
- DSC Troubleshooting Tips 52
- Using DSIP 54
- Investigating Memory Usage 61
- Verifying CPU Utilization 63
- Table 2-5 Local AAA Commands 65
- Setting Up a Log In Banner 66
- Configuring Basic IP 67
- Table 2-7 Alarm Conditions 72
- Table 2-9 IP Routing Commands 77
- Figure 2-6 Test Environment 79
- Operations 83
- Async DataComm Model 84
- Verifying Modem Performance 86
- V.34 Basic Rules 89
- V.90 Basic Rules 90
- Configuring IPCP Options 108
- Configuring LCP Options 109
- Enabling PPP Autoselect 110
- Troubleshooting Flow Diagrams 113
- DOC-7810814= 114
- Chapter 3 Operations 114
- Inspecting Active Call States 116
- Modem Management Operations 122
- Managing Modem Firmware 123
- Inspecting Modem Firmware 124
- Upgrading Modem Firmware 126
- Using Modem Call-Record Terse 136
- Using SNMP 136
- Administration 139
- Table 4-1 RMON Groups 140
- Chapter 4 Administration 141
- Enabling Syslog 142
- Enabling SNMP 145
- Table 4-4 SNMP Commands 146
- XL1 installed 148
- Access Service Security 151
- Configuring RADIUS 152
- RADIUS Operation 153
- AAA Commands 161
- RADIUS Commands 161
- Configuring TACACS+ 162
- Enabling AAA Globally 167
- Identify a List Name 168
- • Users Dialing In Using PPP 170
- Users Dialing In Using PPP 171
- Login Authentication Example 171
- TACACS+ Authorization 172
- Authorization Examples 175
- TACACS+ Security Examples 176
- Maintenance 179
- Chapter 5 Maintenance 180
- Replacement Procedures 180
- Tools and Parts Required 182
- Removing a Power Entry Module 182
- –48V –48V 185
- Replacing a Filter Module 186
- Removing a Filter Module 187
- Replacing the Filter Module 190
- Panel fastener 194
- Connecting the Cables 197
- Replacing a Flash Memory Card 200
- Removing a Flash Memory Card 202
- Replacing the Blower Assembly 203
- Port adapter lever 206
- Slot number 206
- Unlocked position 206
- Locked position 206
- ORK PROCESSING ENGINE-150 211
- Power switches 211
- AC-input power 214
- AC power cable 214
- Figure 5-30.) 217
- Figure 5-31.) 218
- Filter module 219
- Back cover 219
- Backplane module 220
- Replacing the Backplane 221
- Troubleshooting 222
- AS5800 Dial Shelf 223
- Feature Cards 223
- Controller T1 223
- General Configuration 224
- Async Calls 225
- Interactive Async User 225
- Interactive Users 226
- Dedicated-PPP Users 227
- PPP Users 227
- Sync Calls 228
- SGBP Troubleshooting 229
- Provisioning 231
- Figure 6-1 Business Scenario 232
- Chapter 6 Provisioning 233
- Cisco IOS Upgrades 235
- Software Upgrade Requisites 236
- Memory Requirements 236
- Installing New IOS Software 238
- Upgrading the DSC Software 239
- Software Upgrade Verification 242
- Modem Upgrading 243
- Modem Upgrades 244
- Modem Operation at Bootup 247
- Split Dial Shelves 248
- TDM Resource Allocation 249
- Changing Slot Sets 250
- Leaving Split Mode 251
- Managing a Split Dial Shelf 253
- Explanation 254
- Router-Shelf Redundancy 257
- External Services 258
- Configuring Redundancy 258
- Redundancy Show Commands 259
- Advanced Quick Reference 261
- Functional Components 262
- Egress Interface 263
- Loopback Interface 264
- Routing Protocol 265
- Ingress Interface 266
- T3 Ingress Configuration 267
- T1 Ingress Configuration 268
- Line Signaling 269
- D-Channels (ISDN) 270
- D-Channel Configuration 271
- AAA Plan and Requisites 272
- To Modify, Copy, & Paste 273
- Sample Configuration 273
- AAA Accounting Configuration 274
- Command Line Description 275
- Modem Pools 276
- Modem Pool Configuration 277
- TTY Line 278
- Async Interface 279
- Async Interface Configuration 280
- Dial Interface 281
- Dial Interface Configuration 282
- IP Address Pools 283
- Virtual Template 285
- SGBP Requisites 286
- SGBP Configuration 286
- VPDN Requisites 287
- VPDN Configuration 288
- SNMP Requisites 288
- SNMP Configuration 288
- Virtual Profiles 289
- Multilink Virtual Template 290
- V.120 Support 291
- Global Parameters 292
- Global Parameter Requisites 293
- Final Operational Requisites 294
- GLOSSARY 297
- Glossary 298
- World Wide Web (WWW) 315
- OL-0552-01 317
Related products and manuals for Servers Cisco AS5800
Servers Cisco UCS C240 M3 Specifications
(60 pages)
(60 pages)
Servers Cisco 6200 User Manual
(4 pages)
(4 pages)
Servers Cisco UCS C200 Installation Guide
(30 pages)
(30 pages)
Servers Cisco 7008 User Manual
(9 pages)
(9 pages)
Servers Cisco 32369 User Manual
(52 pages)
(52 pages)
Servers Cisco TD 92322GB Installation Guide
(34 pages)
(34 pages)
Servers Cisco AS5800 Installation Guide
(34 pages)
(34 pages)
Servers Cisco 700 Series User Manual
(6 pages)
(6 pages)
© 2020, manymanuals.com. All rights reserved. | 0.806 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals