Cisco Catalyst 8540 MSR Technical Information download pdf (Page 37)

Chapter 3 Initially Configuring the ATM Switch Router

Testing the Configuration

3-37

ATM Switch Router Software Configuration Guide

78-6277-03, Cisco IOS Release 12.0(13)W5(19)

Confirming the ATM Address

Use the show atm addresses command to confirm correct configuration of the ATM address for the

ATM switch router:

Switch# show atm addresses

Switch Address(es):

47.009181000000000100000001.000100000001.00 active

Soft VC Address(es):

47.0091.8100.0000.0001.0000.0001.4000.0c80.9000.00 ATM1/1/0

47.0091.8100.0000.0001.0000.0001.4000.0c80.9010.00 ATM1/1/1

47.0091.8100.0000.0001.0000.0001.4000.0c80.9020.00 ATM1/1/2

47.0091.8100.0000.0001.0000.0001.4000.0c80.9030.00 ATM1/1/3

47.0091.8100.0000.0001.0000.0001.4000.0c81.8000.00 ATM3/0/0

47.0091.8100.0000.0001.0000.0001.4000.0c81.8000.63 ATM3/0/0.99

47.0091.8100.0000.0001.0000.0001.4000.0c81.8010.00 ATM3/0/1

47.0091.8100.0000.0001.0000.0001.4000.0c81.8020.00 ATM3/0/2

47.0091.8100.0000.0001.0000.0001.4000.0c81.8030.00 ATM3/0/3

47.0091.8100.0000.0001.0000.0001.4000.0c81.9000.00 ATM3/1/0

47.0091.8100.0000.0001.0000.0001.4000.0c81.9010.00 ATM3/1/1

47.0091.8100.0000.0001.0000.0001.4000.0c81.9020.00 ATM3/1/2

47.0091.8100.0000.0001.0000.0001.4000.0c81.9030.00 ATM3/1/3

ILMI Switch Prefix(es):

47.0091.8100.0000.0001.0000.0001

ILMI Configured Interface Prefix(es):

LECS Address(es):

Testing the Ethernet Connection

After you have configured the IP address(es) for the Ethernet interface, test for connectivity between the

switch and a host. The host can reside anywhere in your network. To test for Ethernet connectivity, use

the following user EXEC command:

For example, to test Ethernet connectivity from the switch to a workstation with an IP address of

172.20.40.201, enter the command ping ip 172.20.40.201. If the switch receives a response, the

following message displays:

Switch# ping ip 172.20.40.201

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 172.20.40.201, timeout is 2 seconds:

!!!!!

Success rate is 100 percent (5/5), round-trip min/avg/max = 1/202/1000 ms

Command Purpose

ping ip ip-address Tests the configuration using the ping

command. The ping command sends an echo

request to the host specified in the command .

1 ... 36 37 38 39 40 41 42

Comments to this Manuals

No comments

Cisco Catalyst 8540 MSR Technical Information Page 37

Comments to this Manuals

Related products and manuals for Networking Cisco Catalyst 8540 MSR