Cisco 7304 Installation Guide download pdf (Page 73)

6-5

Cisco 7304 Router Modular Services Card and Shared Port Adapter Hardware Installation Guide

OL-4681-01

Chapter 6 Installing and Removing a Shared Port Adapter

Checking the Installation

Note A Fast Ethernet interface is used in the following examples for illustrative purposes.

The following sample display shows the events logged by the system as an MSC with a Fast Ethernet

SPA was removed from module slot 4 in the router. In this example, interface 0 (interface 4/0/0) on the

FastEthernet SPA was up and active when the MSC was removed from the router. Note that the system

logs that the MSC card was removed from slot 4 and that interface 4/0/0 is changed to down.

Router#

00:06:17:%WS_ALARM-6-INFO:ASSERT CRITICAL slot 4 Active Card Removed OIR Alarm

00:06:17:%OIR-6-REMCARD:Card removed from slot 4, interfaces disabled

00:06:18:%LINEPROTO-5-UPDOWN:Line protocol on Interface FastEthernet4/0/0, changed state

to down

When you reinsert the MSC with the installed SPA, the system automatically brings up the interface that

was changed to down when the MSC was removed.

Router#

00:07:29:%OIR-6-INSCARD:Card inserted in slot 4, interfaces administratively shut down

00:07:32:%WS_ALARM-6-INFO:CLEAR CRITICAL slot 4 Active Card Removed OIR Alarm

00:07:35:%LINK-3-UPDOWN:Interface FastEthernet4/0/0, changed state to up

00:07:36:%LINEPROTO-5-UPDOWN:Line protocol on Interface FastEthernet4/0/0, changed state

to up

Use the following procedure to verify that the MSC is installed correctly:

Step 1 Observe the console display messages and verify that the system discovers the MSC, while the system

reinitializes each interface, as follows:

• If you installed a new MSC, the STATUS LED should be green (on). The system should recognize

all new interfaces but leave them configured as administratively down.

• If you replaced an MSC, the STATUS LED should be green (on). The system should recognize each

interface and places each interface in the state that it was previously in before the MSC was

removed.

Step 2 Verify that the STATUS LED on the SPA goes on (is green) and remains on after the reinitialization is

complete. If the STATUS LED remains on, proceed to Step 5. If the STATUS LED does not remain on,

proceed to Step 3.

Step 3 If the STATUS LED on the SPA fails to go on, the SPA or the MSC might not have a compatible FPD

image or the SPA or MSC might not be fully seated even if the SPA locking captive installation screws

are locked. When a SPA is not recognized, the SPA STATUS LED is off. If this occurs in your network,

do the following:

a. Check for system messages indicating an FPD incompatibility or enter the show hw-module

subslot fpd command to ensure the FPD image on the SPA is compatible with the running Cisco

IOS. If an incompatibility exists, an FPD image package file must be downloaded from the Software

Center on Cisco.com and an FPD upgrade must be performed. For information on performing this

upgrade, see the “Upgrading Field-Programmable Devices” chapter of the Cisco 7304 Modular

Services Card and Shared Port Adapter Software Configuration Guide. If the FPD is proven to be

compatible or you are unable to perform the verification steps, proceed with the following steps:

b. Remove the SPA from the MSC.

c. Inspect the SPA. Verify there are no bent pins or parts and that there is nothing lodged in the two

devices that could prevent a good connection.

1 2 ... 68 69 70 71 72 73 74 75 76 77 78 ... 83 84

Comments to this Manuals

No comments

Cisco 7304 Installation Guide Page 73

Comments to this Manuals

Related products and manuals for Routers Cisco 7304