Cisco 2955 Installation Guide Page 94
- Page / 298
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 3 Installation
Connecting the Switch to the Power Converter
3-30
Catalyst 2955 Hardware Installation Guide
78-14944-03
These sections describe the steps required to connect the switch to a power
converter:
• Installing the Power Converter on a DIN Rail, page 3-30
• Connecting the Power Converter to the Power and Relay Connector,
page 3-32
After you connect the switch to the power converter, you must connect the power
converter to an AC or a DC power source.
For instructions on connecting the power converter to an AC power source, see
Connecting the Power Converter to an AC Power Source, page 3-35. For
instructions on connecting the power converter to a DC power source, see
Connecting the Power Converter to a DC Power Source, page 3-41.
Installing the Power Converter on a DIN Rail
Follow these steps to install the power converter on a DIN rail.
Warning
This equipment is supplied as “open type” equipment. It must be mounted
within an enclosure that is suitably designed for those specific environmental
conditions that will be present and appropriately designed to prevent personal
injury resulting from accessibility to live parts. The interior of the enclosure
must be accessible only by the use of a tool.
The enclosure must meet IP 54 or NEMA type 4 minimum enclosure rating
standards.
Statement 1063
Caution To prevent the Catalyst 2955 switch from overheating, there must be a minimum
of 3 inches between any other device and the top, bottom, or sides of the switch.
The power converter requires 1 inch of thermal spacing to prevent overheating.
Therefore, there must be a minimum of 4 inches between the power converter and
the Catalyst 2955 switch to prevent each device from overheating.
- November 2004 1
- CONTENTS 5
- 2 Overview 2-1 6
- 3 Installation 3-1 6
- 5 Troubleshooting 5-1 9
- B Connectors and Cables B-1 9
- Contents 10
- 78-14944-03 10
- Duration of Hardware Warranty 14
- Duration of Software Warranty 14
- Audience 17
- Conventions 18
- Varoitus 19
- Attention 19
- Avvertenza 20
- Advarsel 20
- ¡Advertencia! 21
- Varning! 21
- Related Publications 26
- Obtaining Documentation 26
- Cisco.com 27
- Documentation DVD 27
- Ordering Documentation 27
- Documentation Feedback 28
- • 1 877 228-7302 29
- • 1 408 525-6532 29
- Submitting a Service Request 31
- CLI-Based Setup Program 35
- Taking Out What You Need 36
- Connecting to a Power Source 36
- IP Settings 41
- Completing the Setup Program 41
- Step 10 These choices appear: 44
- Overview 45
- Features 46
- Chapter 2 Overview 46
- Front-Panel Description 47
- 3 Power and relay connector 48
- Warning Labels 49
- 10/100/1000 Ports 51
- Power Status LEDs 56
- 10/100 Port Status LEDs 57
- Uplink Port Status LEDs 58
- Alarm Relay LEDs 60
- Rear-Panel Description 61
- Management Options 63
- • SNMP network management 64
- Installation 65
- Class A Warning for Hungary 72
- • One ferrite 74
- 1 Power and relay connector 90
- Connector 96
- Preparing the AC Power Cord 99
- Statement 42 100
- Chapter 3 Installation 101
- Statement 122 108
- 2 DIN rail 111
- 2 DIN rail clip assembly 117
- Statement 1006 121
- Class 1 LED product 129
- Statement 1027 129
- Statement 1051 131
- Statement 1012 131
- Where to Go Next 133
- Installation in a Hazardous 135
- Environment 135
- Preparing for Installation 136
- EMC Regulatory Statements 142
- VCCI Class A Notice for Japan 143
- Class A Warning for Korea 143
- European Zone 2 Certification 144
- Installation Guidelines 145
- Verifying Package Contents 146
- Verifying Switch Operation 148
- 1 Console cable 150
- Grounding the Switch 152
- Wiring the DC Power Source 155
- Power On the Switch 164
- Running POST 164
- Step 2 Disconnect the cables 166
- Troubleshooting 189
- Understanding POST Results 190
- Diagnosing Problems 191
- Technical Specifications 195
- Catalyst 2955S-12 Switches 196
- Connectors and Cables 201
- 10/100 and 10/100 /1000 Ports 202
- 100BASE-FX Ports 203
- 100BASE-LX Ports 203
- Power and Relay Connector 204
- Console Port 205
- 10/100 ports 206
- 10/100 Ports 207
- Cable and Adapter Pinouts 209
- Connecting to a Terminal 210
- Identifying a Crossover Cable 211
- Translated Safety Warnings 213
- Waarschuwing 219
- Switch Relays Warning 223
- “Open Type” Equipment 230
- Grounded Equipment 234
- Console Cable Connection 236
- Overtemperature Warning 239
- Twisted-pair Supply Wires 244
- Port Connection 247
- Installation Instructions 250
- Service Personnel Warning 251
- Stacking the Chassis Warning 253
- Ground Connection Warning 254
- Jewelry Removal Warning 257
- Product Disposal Warning 259
- Class 1 Laser Product 261
- Class 1 LED Product 262
- Laser Radiation 264
- Laser Viewing Warning 266
- Laser Beam Exposure 268
- Grounded Equipment Warning 278
- Qualified Personnel Warning 280
- Restricted Area 281
- Chassis Power Connection 284
- Exposed DC Power Wire Warning 287
- Numerics 289
Related products and manuals for Network switches Cisco 2955
Network switches Cisco IGX 8 User Manual
(16 pages)
(16 pages)
Network switches Cisco Multiband Swivel-Mount Dipole Antenna AIR-ANTM2050D-R Installation Guide
(84 pages)
(84 pages)
Network switches Cisco EZXS16W User's Guide
(10 pages)
(10 pages)
Network switches Cisco 11506 User Manual
(8 pages)
(8 pages)
Network switches Cisco 3524-PWR - Catalyst XL Enterprise Edition Switch Installation Guide
(144 pages)
(144 pages)
Network switches Cisco ONS 15530 Specifications
(148 pages)
(148 pages)
© 2020, manymanuals.com. All rights reserved. | 0.148 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals