Cisco 15216 EDFA2 Specifications Page 150
- Page / 280
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
9-2
Cisco ONS 15216 EDFA2 Operations Guide
78-16033-01
Chapter 9 TL1 Commands
Notation
9.3.2 Command Code Modifier (ccm)
The command code modifier (ccm) identifies the object of the action being applied by the verb of the
TL1 command. Some command code modifiers for the ONS 15216 EDFA2 are described in Table 9-1.
9.3.3 Access Identifier (aid)
The access identifier (aid) parameter uniquely identifies an object within the ONS 15216 EDFA2. For
the ONS 15216 EDFA2, there are four specific aids (1, PWR-A, PWR-B, EQPT) and the ALL aid, as
described in Table 9-2. All autonomous messages identify their specific aid in the message. For all
command inputs that require an aid as a mandatory parameter, the ALL aid is accepted as well as any
relevant specific aids. If the ALL aid is used in a command, the response contains the appropriate
specific aid. For the commands RTRV-ALM-ENV and RTRV-COND-ENV, inputting a specific aid
filters the response to information relevant to that aid.
9.3.4 Correlation Tag (ctag)
The correlation tag (ctag) is a unique tag associated with a command. If the user specifies a ctag while
entering a command, the response of that command from the ONS 15216 EDFA2 TL1 agent carries the
same ctag value. The ctag consists of no more than six alphanumeric characters.
9.4 Notation
The commands described in this document use the symbols shown in Table 9-3 on page 9-3 to describe
the command format. These symbols are derived from the Telcordia Network Maintenance: Network
Element and Transport Surveillance Messages Manual (Generic Requirements, GR-833-CORE).
Table 9-1 Command Code Modifiers
ccm Description
DWDM Optical parameters.
ENV Environmental (power bus) parameters.
EQPT General parameters of the ONS 15216 EDFA2.
INV Inventory parameters.
NE-GEN IP communications parameters.
Table 9-2 Access Identifiers
aid Description
1 Directly affecting the optical signal.
PWR-A Affecting Power Bus A (or both A and B).
PWR-B Affecting Power Bus B.
EQPT General parameters of the ONS 15216 EDFA2 (not
directly affecting optical signal or power bus).
ALL Any or all of the preceding (command input only).
- Cisco ONS 15216 EDFA2 1
- Operations Guide 1
- CONTENTS 3
- 6 ASH Commands 6-1 5
- 7 FTP Command Line 7-1 7
- 8 Provisioning Using TL1 8-1 7
- 9 TL1 Commands 9-1 8
- 10 Troubleshooting 1 9
- Contents 10
- 78-16033-01 10
- Obtaining Documentation 19
- Documentation Feedback 20
- Cisco.com 20
- Technical Assistance Center 21
- Book Title 22
- Month Year 22
- Applications 23
- 1.3 Key Features 24
- 1.3.1 Constant Gain 25
- 1.3.2 Gain Flattening 25
- 1.3.3 Transient Suppression 26
- 1.3.4 Low Noise 26
- 1.3.5 SNMP MIBs 26
- 1.3.6 TL1 26
- Technical Specifications 27
- 2.1.1 Maximum Input Power 28
- 2.1.2 Channel Loading 28
- °C end of life 29
- 2.4 External Features 30
- 2.5 Front Panel 31
- Front Panel 32
- Installation 33
- Chapter 3 Installation 34
- 3.4 SC/UPC Optical Ports 35
- SC/UPC Optical Ports 36
- 3.5 Communications 37
- 3.5.2 Alarm LEDs 38
- 3.5.2.3 LOS LED (Yellow) 39
- 3.5.2.4 Ethernet Socket LEDs 39
- 3.5.3.1 Required Equipment 39
- Communications 40
- Remote Site 43
- Local Site 43
- 3.5.4.2 Modem Signals 44
- 3.5.4.3 Modem Power Up 44
- Table 3-6 Modem Settings 45
- GND RXD TXD 46
- 4.2 Set IP Address 51
- 4.4 Set Date and Time 52
- 4.7 Set Gain 53
- 4.8 Set Alarm Thresholds 53
- °C. Valid entries 56
- °C. Valid 57
- °C. Valid entries are 57
- °C. Setting this value to 57
- 4.9 Set Password 58
- 4.10 Add Users 59
- 4.11 Save Changes 59
- 4.12 Log Off 60
- Step 3 Save the changes 61
- 5.1 SNMP Overview 63
- 5.1.2.1 SNMP Agent 64
- 5.1.2.2 SNMP MIB 65
- 5.1.2.3 SNMP Manager 65
- SNMP Overview 66
- • Creating a View, page 5-6 67
- 5.2.1 Creating a View 68
- 5.2.2.1 Set CommunityEntry 69
- 5.3 Setup for CTM Access 72
- 5.4 Tables and Groups 73
- 5.4.1 CfgGroup Table 74
- Tables and Groups 75
- 5.4.2 PumpCfgEntry Table 76
- 5.4.4 OverallControl Table 80
- 5.4.5 PumpStatusEntry Table 80
- 5.4.6 AlarmEntry Table 81
- 5.4.7 OpGroup Table 82
- 5.5 Setting Up Traps 83
- 5.5.1 Display Trap Command 84
- 5.5.2 Set Trap Command 85
- 5.5.3 Set Agent Trap Enable 85
- 5.6 Retrieving Information 86
- 5.6.2 Date and Time 87
- 5.6.3 Power Gain 88
- 5.6.4 Case Temperature 89
- 5.6.4.2.2 CtmpMax 90
- 5.6.4.3.1 CtmpMaxHysteresis 90
- 5.6.5 Power Bus 91
- 5.6.6 Input Power (Signal) 92
- 5.6.7 Output Power 93
- 5.6.7.1.2 OutPowerdBm 94
- 5.6.7.2.1 LpoutSetpoint 94
- 5.6.7.2.2 LpoutDeviation 95
- Retrieving Information 97
- 5.6.9 Alarm Entry 98
- 5.7 Summary of SNMP Alarms 99
- Summary of SNMP Alarms 100
- ASH Commands 101
- Chapter 6 ASH Commands 102
- 6.2 Configuration Commands 106
- 6.3 Administrative Commands 110
- 6.3.1 clear Command 111
- 6.3.2 exit Command 111
- 6.3.3 help Command 111
- 6.3.4 history Command 111
- 6.4 Shell Commands 112
- 6.5.1 ffs file list Command 114
- 6.6 SNMP Commands 115
- Command snmp attribute list 116
- 6.6.5 snmp mib get Command 118
- 6.6.6 snmp mib list Command 118
- 6.6.8 snmp row get Command 120
- 6.6.9 snmp row set Command 120
- Command snmp subtree list 122
- 6.7 User Commands 125
- 6.9 Restore Commands 131
- 6.10 Manufacturer Mode 132
- FTP Command Line 133
- 7.2 FTP Commands 135
- FTP Commands 136
- Provisioning Using TL1 137
- 8.2 Set IP Address 139
- 8.4 Set Date and Time 140
- 8.7 Set Gain 141
- 8.8 Set Alarm Thresholds 141
- CISCO ONS 15216 142
- ALARM OUT 142
- Set Alarm Thresholds 144
- 8.9 Set Password 146
- 8.10 Add Users 147
- 8.11 Log Off 147
- TL1 Commands 149
- 9.4 Notation 150
- Chapter 9 TL1 Commands 151
- 9.7.1 ACT-USER 157
- 9.7.2 ALW-MSG-ALL 157
- 9.7.3 APPLY 159
- 9.7.4 CANC-USER 160
- 9.7.5 COPY-RFILE 160
- 9.7.6 CPY-MEM 162
- 9.7.7 DLT-RFILE 163
- 9.7.8 DLT-USER-SECU 164
- 9.7.9 ED-DAT 164
- 9.7.10 ED-DWDM 165
- 9.7.11 ED-ENV 166
- 9.7.12 ED-NE-GEN 167
- 9.7.13 ED-PID 168
- 9.7.14 ED-USER-SECU 169
- 9.7.15 ENT-USER-SECU 169
- 9.7.16 INH-MSG-ALL 170
- 9.7.17 INIT-SYS 173
- 9.7.18 REPT ALM DWDM 173
- 9.7.19 REPT ALM ENV 175
- 9.7.20 REPT ALM EQPT 176
- 9.7.22 REPT EVT FXFR 180
- 9.7.23 RTRV-ALM-ALL 181
- 9.7.24 RTRV-ALM-DWDM 183
- 9.7.25 RTRV-ALM-ENV 185
- 9.7.26 RTRV-ALM-EQPT 186
- 9.7.27 RTRV-AO 188
- 9.7.28 RTRV-COND-ALL 189
- 9.7.29 RTRV-COND-DWDM 191
- 9.7.30 RTRV-COND-ENV 192
- 9.7.31 RTRV-COND-EQPT 194
- 9.7.32 RTRV-DFLT-SECU 195
- 9.7.33 RTRV-DWDM 196
- 9.7.34 RTRV-ENV 198
- 9.7.35 RTRV-HDR 199
- 9.7.36 RTRV-INV 199
- 9.7.37 RTRV-NE-GEN 200
- 9.7.38 RTRV-RFILE 202
- 9.7.39 RTRV-TH-DWDM 203
- 9.7.40 RTRV-TH-ENV 204
- 9.7.41 RTRV-TH-EQPT 205
- 9.7.42 RTRV-TOD 207
- 9.7.43 RTRV-USER-SECU 208
- 9.7.44 SET-ATTR-SECUDFLT 208
- 9.7.45 SET-TH-DWDM 209
- 9.7.46 SET-TH-ENV 210
- 9.7.47 SET-TH-EQPT 211
- 9.7.48 STA-LOCL-RST 212
- Troubleshooting 213
- 10.1 Alarm Indicators 214
- 10.1.1.2 FAIL LED (Red) 215
- 10.1.1.3 LOS LED (Yellow) 215
- 10.1.2 Optical Alarms 216
- Alarm Indicators 217
- 10.1.3 Equipment Alarms 218
- 10.1.4 Environmental Alarms 219
- 10.2.4 Boot Up Failure 220
- 10.2.8 Lost Password 222
- Regulatory Compliance 225
- Translated Safety Warnings 226
- Warning Definition 228
- DC Power Supply Warning 230
- Installation Warning 231
- Power Cord Warning 231
- No On/Off Switch Warning 232
- SELV Circuit Warning 233
- Laser Radiation Warning 234
- Laser Beam Warning 235
- Power Cabling Warning 235
- Grounded Equipment Warning 236
- Ground Connection Warning 237
- Jewelry Removal Warning 238
- Qualified Personnel Warning 239
- Supply Circuit Warning 239
- Power Supply Wiring Warning 240
- Incorrect Connection Warning 242
- Ground Conductor Warning 243
- More Than One Power Supply 245
- Exposed DC Power Wire Warning 246
- 48 VDC Power System 247
- Chassis Power Connection 248
- Product Disposal Warning 252
- Energy Hazard 253
- Ground Wire Warning 256
- Class B EMC Warning 259
- Safety Requirements Warning 259
- Optical Connector Warning 262
- Eye Damage Warning 263
- Static Electricity Warning 264
- Connector Cleaning Warning 265
- Module Removal Warning 267
- Reinforced Insulation Warning 269
- Power Supply Voltage Warning 270
- Avvertenza 271
- Advarsel 271
- ¡Advertencia! 271
- Varning! 271
Related products and manuals for Networking Cisco 15216 EDFA2
Networking Cisco 4430 User Manual
(12 pages)
(12 pages)
Networking Cisco MGX 8230 Specifications
(282 pages)
(282 pages)
Networking Cisco 3620 Installation Guide
(36 pages)
(36 pages)
Networking Cisco Ethernet switch User Manual
(84 pages)
(84 pages)
Networking Cisco TES301 User's Guide
(98 pages)
(98 pages)
Networking Cisco 7300-6T3 Specifications
(50 pages)
(50 pages)
Networking Cisco 813 Specifications
(112 pages)
(112 pages)
Networking Cisco Engine 611 Specifications
(718 pages)
(718 pages)
Networking Cisco 3745 Installation Guide
(32 pages)
(32 pages)
© 2020, manymanuals.com. All rights reserved. | 0.043 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals