Cisco MGX 8950 Specifications Page 160
- Page / 642
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
3-32
Cisco MGX 8850 (PXM1E/PXM45), Cisco MGX 8950, Cisco MGX 8830, and Cisco MGX 8880 Configuration Guide
Release 5.0.10, OL-3845-01 Rev. B0, August 16, 2004
Chapter 3 Provisioning PXM1E Communication Links
General PXM1E Configuration Procedures
M8830_CH.1.PXM.a > dspimagrps
Ima Min Tx Rx Tx Diff NE-IMA FE-IMA IMA
Grp Lnks Frm Frm Clk Delay State State Ver
Len Len Mode (ms)
--------------------------------------------------------------------------------
2.1 1 128 128 CTC 275 Operational Operational 1.0
Step 3 To display the configuration information for the particular IMA group that you want to configure, enter
the dspimagrp <group> command. The IMA group numbers are listed in the Ima Grp column. In the
following example, the user displays the IMA group 2.1.
M8830_CH.1.PXM.a > dspimagrp 2.1
Group Number : 2.1
NE IMA Version : 1.0
Group Symmetry : Symm Operation
Tx Min Num Links : 1
Rx Min Num Links : 1
NE Tx Clk Mode : CTC
FE Tx Clk Mode : CTC
Tx Frame Len (bytes) : 128
Rx Frame Len (bytes) : 128
Group GTSM : Up
NE Group State : Operational
FE Group State : Operational
Group Failure Status : No Failure
Tx IMA ID : 255
Rx IMA ID : 255
Max Cell Rate (c/s) : 14367
Avail Cell Rate (c/s) : 14367
Diff Delay Max (msecs) : 275
Diff Delay Max Observed (msecs) : 0
Accumulated Delay (msecs) : 0
Clear Accumulated Delay Status : Not In Progress
GTSM Up Integ Time (msecs) : 0
Type <CR> to continue, Q<CR> to stop:
GTSM Dn Integ Time (msecs) : 4000
Num Tx Cfg Links : 4
Num Rx Cfg Links : 4
Num Act Tx Links : 4
Num Act Rx Links : 4
Least Delay Link : 2.4
Tx Timing Ref Link : 2.4
Rx Timing Ref Link : 2.1
Group Running Secs : 3999077
Alpha Val : 2
Beta Val : 2
Gamma Val : 1
Tx OAM Label : 1
Rx OAM Label : 1
Test Pattern Procedure Status : Disabled
Test Link : Unknown
Test Pattern : 255
Stuff Cell Indication (frames) : 1
Version Fallback Enabled : true
Auto-Restart Mode : disable
Rx IMA ID Expected : -1
Auto-Restart Sync State : disable
- MGX 8880 Configuration Guide 1
- CONTENTS 3
- Contents 10
- D Standards Compliance D-1 16
- F MPSM Licensing F-1 17
- Command Parameters 7-8 22
- About This Guide 27
- Conventions 28
- Documentation 29
- Related Documentation 30
- Obtaining Documentation 43
- Changes to This Document 44
- Documentation Feedback 46
- Cisco TAC Website 46
- Opening a TAC Case 47
- TAC Case Priority Definitions 47
- Preparing for Configuration 49
- Cisco MGX Switch Features 51
- Physical Attributes 52
- Services 52
- Trunk/Port Interfaces 53
- Supported Controller Cards 55
- Supported Routing Protocols 55
- Supported Services 55
- Typical Topologies 58
- Core Switch 59
- Multiservice Edge Aggregation 59
- Configuration Overview 61
- Collecting Information 62
- Administrator Data 63
- Unique Device Identifier 63
- Administrator Access Method 64
- Network Clock Source Plan 64
- Network Management Plan 64
- • manual 67
- Initializing the Switch 76
- Getting Command Help 84
- Configuring User Access 87
- Adding Users 88
- Deleting Users 91
- Adding the PNNI Controller 95
- Setting the PNNI Node Address 97
- Setting the PNNI Node ID 99
- Configuring Clock Sources 102
- UI-S3/B 104
- Enabling NCDP on a Node 106
- Setting the LAN IP Addresses 108
- Setting the Disk IP Address 111
- • SMFLR-1-2488 123
- Note No traffic 123
- • SMFSR-1-2488 123
- • SMFIR-1-155-SFP 124
- • SMFLR-1-155-SFP 124
- • MMF-1-155-SFP 126
- Line Configuration Quickstart 130
- SVC Configuration Quickstart 135
- Configuring the Card Mode 149
- Setting Up Lines 150
- Configuring Lines 151
- Configuring T1 (DS1) Lines 152
- Configuring E1 Lines 153
- Configuring SONET Lines 154
- Configuring T3 Lines 154
- Configuring E3 Lines 155
- Verifying Line Configuration 156
- Creating an IMA Group 157
- • Version 1.0 = 1 158
- • Version 1.1 = 2 158
- Configuring an IMA Group 159
- Configuring IMA Links 164
- Adding an IMA Port 165
- Working line 168
- Midplane 168
- Protection line 168
- PXM-UI-S3/B back card 168
- Adding ATM Ports 172
- Modifying ATM Ports 175
- Configuring ILMI on a Port 188
- Note 0 = no polling 190
- Verifying PNNI Communications 195
- • 0 = persistent 203
- • 1 = nonpersistent 203
- Bringing Down a Connection 214
- Bringing Up a Connection 215
- Bringing Down a Party 215
- Bringing Up a Party 215
- Rerouting Connections 215
- Rerouting a P2MP Party 215
- Deleting Connections 216
- IGX Feeder Topology 217
- Deleting an IGX Feeder 218
- Configuration Quickstart 222
- Initializing Service Modules 224
- Selecting a Card SCT 229
- Selecting a Port SCT 231
- • Bulk distribution 233
- Configured for SONET/SDH 234
- Configured for T3 Interfaces 235
- Setting Up SRM Lines 236
- Configuring a SONET/SDH Line 237
- Where To Go Next 251
- Initializing RPM Cards 256
- Where to Go Next 263
- Cisco SCTs 266
- Managing SCTs 268
- SCT File Naming Convention 269
- Registering SCT Files 271
- Command Parameters 272
- Updating Registered SCT Files 273
- Deleting a Registered SCT 275
- Deleting Unregistered SCTs 276
- Managing Card SCTs 277
- Managing PXM1E Port SCTs 277
- Changing a Port SCT 278
- Displaying Port SCT Settings 279
- • 0 is highest priority 286
- • 15 is lowest priority 286
- Managing PNNI Nodes 291
- Configuring PNNI Timers 299
- Managing PNNI Routes 300
- Managing Preferred Routes 301
- Creating a Preferred Route 304
- Modifying a Preferred Route 307
- Deleting a Preferred Route 309
- Configuring the Deroute Delay 313
- Pure PXM45/C Networks 314
- Managing Priority Routing 315
- Managing Priority Bumping 319
- Managing Connection Grooming 322
- Slave endpoin 324
- Manually Grooming Connections 328
- • Cell transfer delay (CTD) 329
- • Cell delay variation (CDV) 329
- • Administrative Weight (AW) 329
- Configuring Orderly Grooming 333
- Configuring the AIS Delay 337
- Displaying System Addresses 340
- Displaying the SVCC RCC Timer 344
- Displaying the SVCC RCC Table 345
- Managing CUGs 346
- Creating Closed User Groups 347
- Deleting a CUG Assignment 354
- Blocking the CUG IE 354
- Configuring a Gateway Node 355
- • network topology database 357
- • link topology database 357
- • feeder topology database 357
- Displaying Link Information 359
- Displaying Feeder Information 361
- Disabling a Gateway Node 362
- Switch Operating Procedures 365
- Clearing a Slot Configuration 368
- Managing ILMI 371
- Deleting ILMI Prefixes 375
- Managing Redundant Cards 380
- Managing Redundant APS Lines 382
- Preparing for Intercard APS 383
- Modifying APS Lines 388
- Switching APS Lines 389
- Troubleshooting APS Lines 390
- Managing NCDP Clock Sources 395
- Enabling NCDP on a Switch 396
- Configuring an NCDP Port 398
- Displaying NCDP Information 399
- Display An NCDP Port 403
- Deleting an NCDP Clock Source 404
- Delete Manual Clock Sources 406
- Displaying SVCs 407
- Managing Controllers 407
- Adding Controllers 408
- Deleting a Controller 409
- Managing PXM1E Partitions 410
- Removing Static ATM Addresses 415
- Managing Load Sharing 419
- Starting a Telnet Session 421
- Displaying a Telnet Trace 422
- Switches 424
- Configuring AAA Servers 427
- Verifying PXM Disk Data 437
- Configuring a Line Loopback 443
- Managing Bit Error Rate Tests 444
- Managing IMA 455
- Displaying IMA Links 456
- Deleting an IMA Group 457
- Deleting an IMA Link 457
- Restarting an IMA Group 457
- Switch Maintenance Procedures 461
- Adding Cards 462
- Adding SRM Cards 464
- Adding RPM Cards 465
- Replacing Cards 466
- Upgrading a Standalone AXSM 478
- Replacing Service Modules 480
- Decommissioning an AXSM Slot 486
- Decommissioning an RPM Slot 488
- Controls 489
- Displaying Node Alarms 490
- Displaying Clock Alarms 490
- Displaying Switching Alarms 490
- • dspXbarPlaneAlms 491
- • dspxbarslotbwalms 491
- Displaying Environment Alarms 493
- Displaying Card Alarms 494
- Displaying IMA Alarms 496
- Displaying License Alarms 497
- Upgrade Process Overview 501
- PXM and AXSM Boot Downgrades 522
- Browsing the File System 524
- Locating Software Updates 525
- Starting the Upgrade Software 533
- Upgrading RPM Boot Software 536
- PXM Backup Boot Procedures 549
- APPENDIX 555
- Workstatio 556
- Serial cable 556
- PXM-UI-S3 556
- Workstation 560
- Configuring the Switch 562
- Configuring the Router 564
- Server Connection 565
- Starting a CLI Telnet Session 566
- Standards Compliance 571
- ATM Signaling Compliance 572
- PNNI Signaling 573
- ATM Signaling Interworking 574
- SONET/SDH 574
- Worksheets 575
- Hardware Survey Worksheets 576
- PXM and SRM 581
- AXSM Configuration Worksheet 586
- CESM Configuration Worksheet 587
- Worksheet 589
- VISM Configuration Worksheet 593
- VXSM Configuration Worksheet 594
- MPSM Licensing 595
- MPSM Licensing Information 596
- PXM License Pool 600
- Displaying License Data 601
- Note Go to Step 7 610
- Note Skip to Step 9 611
- MPSM License Alarms 612
- Slot License Alarms 613
- Rekeying Feature Licenses 615
- Diagnostics 619
- Diagnostics Examples 620
- Diagnostics Tests 622
- PXM45 Diagnostics Tests 623
- PXM45 Path Tests 624
Related products and manuals for Network switches Cisco MGX 8950
Network switches Cisco ME 3600X User Manual
(10 pages)
(10 pages)
Network switches Cisco NTP-E157 User Manual
(167 pages)
(167 pages)
Network switches Cisco IGX 8 Specifications
(298 pages)
(298 pages)
Network switches Cisco 8600 Specifications
(129 pages)
(129 pages)
Network switches Cisco 3040 Specifications
(99 pages)
(99 pages)
© 2020, manymanuals.com. All rights reserved. | 0.749 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals