Cisco RPM-XF Specifications download pdf (Page 120)

100

101

3-38

Cisco ATM Services (AXSM) Configuration Guide and Command Reference for MGX Switches

Release 5.2, Part Number OL-6484-01 Rev. C0, September 2005

Chapter 3 Provisioning ATM Services

General AXSM Configuration Procedures

M8850_LA.12.AXSME.a > dspimalnk 1.1.3:1.1

IMA Link Number : 1.1.3:1.1

IMA Link Group Number : 1

Link Rel Delay (msecs) : 0

Link NE Tx State : Unusable-Failed

Link NE Rx State : Not In Grp

Link FE Tx State : Not In Grp

Link FE Rx State : Not In Grp

Link NE Rx Failure Status : Link Fail

Link FE Rx Failure Status : No Failure

IMA Link Tx LID : 0

IMA Link Rx LID : 255

Link Rx Test Pattern : 255

Link Test Procedure Status : Disabled

Link LIF Integ UpTime : 25000

Link LIF Integ DownTime : 1000

Link LODS Integ UpTime : 25000

Link LODS Integ DownTime : 1000

Adding an IMA Port to an IMA Group

After you have configured an IMA group, you need to add a port to an IMA group to make it fully

operational. Use the following procedure to add an IMA port to a group.

Step 1 Establish a configuration session using a user name with GROUP1 privileges or higher.

Step 2 Get the group number on which you will add the port. To display a list of the IMA group numbers, enter

the dspimagrps command.

Step 3 Verify that the link and port number you want to use is not configured. To display a list of the ports

configured on the AXSM-32-T1E1-E card, enter the dspports command, as follows:

8850_LA.2.AXSM.a > dspports

ifNum Line Admin Oper. Guaranteed Maximum SCT Id ifType VPI minVPI maxVPI

State State Rate Rate (D:dflt (VNNI, (EVNNI,EVUNI)

used) VUNI)

----- ---- ----- ----- ---------- --------- ------ ------ ------ ------ ------

1 2.1 Up Down 1412830 1412830 5 NNI 0 0 0

2 2.2 Up Down 1412830 1412830 5 NNI 0 0 0

3 1.1 Up Up 1412830 1412830 5 NNI 0 0 0

This command displays all ports on the AXSM-32-T1E1-E card in the ifNum (interface number)

column. Pay attention to the port numbers already in use. When you add a port, you must specify a port

number that is unique on the AXSM-32-T1E1-E card. For example, if port number 5 is assigned to line

1.1, you cannot use port 5 on any other line on that AXSM-32-T1E1-E card.

Note The Cisco MGX 8850 (PXM45) and Cisco MGX 8950 support one port per line.

Step 4 To add an ATM port to a group, enter the addimaport command as follows:

addimaport <ifNum> <group> <guaranteedRate> <maxRate> <sctID> <ifType> [-vpi <vpi>] [-minvpi

<minvpi>] [-maxvpi <maxvpi>]

Table 3-8 lists the parameter descriptions for adding IMA ports.

1 ... 119 120 121 ... 688

Comments to this Manuals

No comments

Cisco RPM-XF Specifications Page 120

Comments to this Manuals

Related products and manuals for Networking Cisco RPM-XF