Cisco RPM-XF Specifications Page 255
- Page / 688
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
5-45
Cisco ATM Services (AXSM) Configuration Guide and Command Reference for MGX Switches
Release 5.2, Part Number OL-6484-01 Rev. C0, September 2005
Chapter 5 AXSM Command Reference
addrscprtn
addrscprtn
Add Resource Partition—AXSM, AXSM-E, AXSM-32-T1E1-E, AXSM-XG
Add a logical partition of resources for a network controller on a port. Before you add resource
partitions, be sure a plan exists for future developments, such as the addition of a new controller.
Note The addpart and addrscprtn commands are identical. Use the command name that suits you. The same
identification applies to commands that display and delete a resource partition.
A resource partition consists of:
• Guaranteed percentage of bandwidth.
• VPI and VCI ranges. For MPLS (or LSC), Cisco Systems recommends a minimum VCI of 35.
• Guaranteed minimum and maximum number of connections.
Note The maximum number of connections must be greater than 10.
Before adding a resource partition, you must:
• Activate physical lines on the card (upln and optional cnfln).
• Add logical ports to the physical lines (addport and optional cnfport).
• Execute addcontroller on the PXM45 to identify a controller type to the Cisco Virtual Switch
Interface (VSI) and give that controller an ID number. The addrscprtn command takes this
controller ID as an argument.
The primary network control application is PNNI. Plan the partitioning for possible use of MPLS or
other controllers in the future.
Note For VNNIs (virtual trunks), you can configure one VNNI per port and one port per partition. Specify the
VNNI interface type through the addport command.
AXSM-E, AXSM-XG Dependencies
A dependency exists between the addcontroller command on the PXM45 and the addpart
(addrscprtn) command on the AXSM-E and AXSM-XG. Both commands take a controller ID (ctrlr_id)
as an input. Both of these controller IDs must be the same when referring to the same VSI controller.
The sequence for executing these two commands should be as follows:
1. Run addcontroller on the PXM45 to specify the location of the VSI controller.
2. Run addpart (addrscprtn) on the AXSM-E and AXSM-XG to add resource partitions for the VSI
controller.
To support legacy service modules and earlier implementations of VSI, only the following combinations
of controller ID (ctrlr_id) values 1, 2, and 3 and controller type (cntrlrType) values are supported:
• controller ID value 1 and controller type value 1 (PAR)
(Controller type (cntrlrType) is an addcontroller parameter.)
• controller ID value 2 and controller type value 2 (PNNI)
• controller ID value 3 and controller type value 3 (MPLS)
- Switches 1
- CONTENTS 3
- 4 AXSM Card Management 4-1 5
- 5 AXSM Command Reference 5-1 7
- Contents 10
- About This Guide 21
- Conventions 22
- Documentation 22
- Related Documentation 23
- Obtaining Documentation 36
- Documentation Feedback 37
- Submitting a Service Request 38
- Introduction 41
- Command Line Interface 42
- CLI Syntax 43
- AXSM Models 44
- Chapter 1 Introduction 45
- Logical Ports 46
- Common Acronyms 46
- List of Commands by Function 47
- Preparing for Provisioning 57
- AXSM Service Class Templates 63
- Setting Up Lines 65
- Bringing Up Lines 66
- Configuring Lines 68
- LineType 69
- Verifying Line Configuration 70
- Adding Intracard APS Lines 71
- Adding Intercard APS Lines 72
- Table 2-7 Line Channelization 73
- Channelizing a Line 74
- Channelizing a SONET Line 77
- Channelizing an SDH Line 79
- Provisioning ATM Services 83
- • Cisco MGX 8230 84
- • Cisco MGX 8250 84
- • Cisco MGX 8850 (PXM1E) 84
- • Cisco IGX switches 84
- SVC Configuration Quickstart 89
- Adding ATM Ports 109
- Creating an IMA Group 116
- • AXSM: 1–60 125
- • AXSM-E: 1–32 125
- Configuring ILMI on a Port 129
- Configuring PNNI Links 136
- Defining a Feeder Port 140
- AXSM Card Management 149
- Managing CLI Sessions 150
- Managing Cards 151
- Managing Card SCTs 152
- Displaying Card SCT Settings 154
- Managing Port SCTs 157
- Selecting a Port SCT 158
- Changing a Port SCT 158
- Displaying Port SCT Settings 159
- Port SCT ABR Parameters (abr) 178
- Managing Lines 179
- Bringing Down a Line 180
- Managing Ports 181
- Deleting Ports 185
- Delete an ATM Port 186
- Managing Resource Partitions 187
- Managing Connections 192
- Deleting ATM Connections 194
- Rerouting a P2MP Party 196
- Testing ATM Connections 198
- Verifying PNNI Communications 200
- Managing IMA Groups 203
- Configuring IMA Groups 205
- • 1 = IMA version 1.0 206
- • 2 = IMA version 1.1 206
- Configuring an IMA Link 207
- Deleting an IMA Group 208
- Testing an IMA Link 209
- Managing Loopbacks 210
- AXSM Command Reference 211
- APS Overview 212
- APS Architecture Modes 212
- AXSM/A and AXSM/B APS Issues 214
- Syntax Description 214
- Related Commands 215
- Attributes 215
- Before Adding a Connection 218
- Adding a Connection 218
- Traffic Parameters 219
- Service Types, CDV, and CTD 220
- Routing Parameters 221
- Frame Discard 221
- Restrictions 222
- Local-Only Parameters 223
- OAM and Failure Management 225
- Syntax (AXSM) 225
- • 1 = enable 229
- Error Messages 231
- Value 1.3 2 4 3 64 1 275 236
- Setting the Correct Port SCT 238
- Usage Guidelines 241
- Related Command 241
- Syntax Description (AXSM) 243
- -ds3 1.16 244
- AXSM-E, AXSM-XG Dependencies 247
- Using the Correct SCT 250
- Syntax (AXSM-XG) 251
- Example 261
- • AXSM-E : 1–32 270
- • AXSM-XG: 1–126 270
- Examples 278
- Attributes (AXSM) 291
- Attributes (AXSM-E, AXSM-XG) 291
- Display Command History 302
- Configuration successful 305
- Generic Syntax Description 306
- Thresholds for SONET Section 307
- Thresholds for SONET Line 307
- Thresholds for SONET Path 307
- Thresholds for DS3 308
- Thresholds for E3 308
- Thresholds for PLCP 308
- Table 5-15 BERT Test Patterns 318
- Background 322
- Types of Card Statistics 325
- Syntax (SONET) 347
- Syntax Description (SONET) 347
- Syntax (DS3) 347
- Syntax Description (DS3) 348
- Syntax (E1) 349
- Syntax Description (E1) 349
- Syntax (E3) 349
- Syntax Description (E3) 349
- <SEFS24Hr> 351
- Syntax (Sonet Lines) 352
- 15-minute intervals to 500 353
- Chapter 5 354
- <SEFS24>] 359
- Specifying the Core Mask 375
- Redundancy Policy 376
- Aborting a Core Dump 376
- Example (AXSM-E) 388
- Example (AXSM-32-T1E1-E) 388
- AXSM, AXSM-E, AXSM-XG) 400
- Attributes (AXSM-32-T1E1-E) 401
- Example (AXSM) 435
- Example (AXSM-XG) 436
- Syntax (AXSM-E, AXSM-XG) 442
- Example (SCT 2) 443
- Example SCT 3 445
- Step 1 Execute tstdelay 458
- Step 2 Check the results 458
- • ATLAS programmed data 465
- • SABRE programmed data 465
- The dspcons Output on AXSM 472
- Syntax Description 498
- Example 499
- Attributes 500
- alarm type 513
- Syntax (AXSM, AXSM-XG) 523
- Syntax (AXSM-E) 523
- (AXSM-E) 523
- Display Output 523
- Display Lines—AXSM 539
- Version Numbering Conventions 623
- Firmware Filenames 623
- Version Numbers 623
Related products and manuals for Networking Cisco RPM-XF
Networking Cisco IAD2431-16FXS User's Guide
(94 pages)
(94 pages)
Networking Cisco 2613 User Manual
(16 pages)
(16 pages)
Networking Cisco IOS Router User Manual
(9 pages)
(9 pages)
Networking Cisco NM-HDV-1E1-30E - 30 Enhanced Channel E1 Voice/Fax Network Module Service Manual
(24 pages)
(24 pages)
Networking Cisco 15216 EDFA2 Specifications
(252 pages)
(252 pages)
Networking Cisco EZXS88W User's Guide
(10 pages)
(10 pages)
Networking Cisco DPC 3925 User's Guide
(106 pages)
(106 pages)
Networking Cisco OL-6900-01 User Manual
(126 pages)
(126 pages)
Networking Cisco RT31P2-NA User Manual
(73 pages)
(73 pages)
Networking Cisco 675E User's Guide
(50 pages)
(50 pages)
(15 pages)
Networking Cisco PXM Version 1.1 User's Guide
(972 pages)
(972 pages)
Networking Cisco uBR904 Specifications
(38 pages)
(38 pages)
© 2020, manymanuals.com. All rights reserved. | 0.084 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals