Cisco RPM-XF Specifications Page 459
- Page / 688
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
5-249
Cisco ATM Services (AXSM) Configuration Guide and Command Reference for MGX Switches
Release 5.2, Part Number OL-6484-01 Rev. C0, September 2005
Chapter 5
dspcon
dspcon
Display Connection—AXSM, AXSM-E, AXSM-32-T1E1-E, AXSM-XG
Display information about an SPVC. The contents of the display on the AXSM and the PXM45 differ
slightly. On both cards, the dspcon output appears in sections to make the information easier to sort.
Most of the information in the dspcon output comes from addcon execution. See the addcon description
for more information. Also, executing cnfpnni-intf can affect the dspcon output.
Display Connection on the AXSM
On the AXSM, dspcon shows the following connection identifiers:
• NSAP address, logical port, VPI/VCI, status, and ownership of local and remote ends of the
connection. The display shows whether a particular endpoint is the master or slave.
The provisioning parameters in the display show:
• Connection type of VPC or VCC.
• Service type (for example, ABR).
• A number indicating the controller. For example, 2 refers to PNNI. The addcontroller command
specifies the controller.
• The administrative state is either up or down. This state results from addcon or dncon/upcon. Note
that, after you down a connection with at the connection master endpoint, the dspcon command
shows the connection as “down” when you execute it at the master endpoint and “failed” when you
execute it at the slave endpoint. (See also dncon description).
• The operational state is either OK or failed. The operational state can apply to a connection
regardless of the administrative state.
The traffic management parameters consist of:
• Local and remote UPC parameters of PCR, MBS, CTD, CDVT, and so on. A –1 in a field means that
the parameter was not specified. The characters “N/A” indicate that the parameter does not apply to
the service type.
These other fields also pertain to connection integrity:
• OAM connectivity check enable or disable.
• Loopback test enable/disable and loopback type.
• Round trip delay in microseconds. This field is non-zero only if you previously executed tstdelay.
The dspcon command requires a unique connection identifier. If you do not have the information to
identify a connection, execute dspcons. On the AXSM, dspcons identifies all the connections on the
AXSM. On the PXM45, dspcons identifies all the connections on the node. (See dspcons description).
Display Connection on the AXSM-E, AXSM-32-T1E1-E, AXSM-XG
The display output on the AXSM-E and AXSM-XG also displays RDI (Remote Defect Indication)
information at the ATM Layer through the OAM mechanism in Ingress and Egress directions.
Syntax
dspcon <ifNum> <vpi> <vci>
- Switches 1
- CONTENTS 3
- 4 AXSM Card Management 4-1 5
- 5 AXSM Command Reference 5-1 7
- Contents 10
- About This Guide 21
- Conventions 22
- Documentation 22
- Related Documentation 23
- Obtaining Documentation 36
- Documentation Feedback 37
- Submitting a Service Request 38
- Introduction 41
- Command Line Interface 42
- CLI Syntax 43
- AXSM Models 44
- Chapter 1 Introduction 45
- Logical Ports 46
- Common Acronyms 46
- List of Commands by Function 47
- Preparing for Provisioning 57
- AXSM Service Class Templates 63
- Setting Up Lines 65
- Bringing Up Lines 66
- Configuring Lines 68
- LineType 69
- Verifying Line Configuration 70
- Adding Intracard APS Lines 71
- Adding Intercard APS Lines 72
- Table 2-7 Line Channelization 73
- Channelizing a Line 74
- Channelizing a SONET Line 77
- Channelizing an SDH Line 79
- Provisioning ATM Services 83
- • Cisco MGX 8230 84
- • Cisco MGX 8250 84
- • Cisco MGX 8850 (PXM1E) 84
- • Cisco IGX switches 84
- SVC Configuration Quickstart 89
- Adding ATM Ports 109
- Creating an IMA Group 116
- • AXSM: 1–60 125
- • AXSM-E: 1–32 125
- Configuring ILMI on a Port 129
- Configuring PNNI Links 136
- Defining a Feeder Port 140
- AXSM Card Management 149
- Managing CLI Sessions 150
- Managing Cards 151
- Managing Card SCTs 152
- Displaying Card SCT Settings 154
- Managing Port SCTs 157
- Selecting a Port SCT 158
- Changing a Port SCT 158
- Displaying Port SCT Settings 159
- Port SCT ABR Parameters (abr) 178
- Managing Lines 179
- Bringing Down a Line 180
- Managing Ports 181
- Deleting Ports 185
- Delete an ATM Port 186
- Managing Resource Partitions 187
- Managing Connections 192
- Deleting ATM Connections 194
- Rerouting a P2MP Party 196
- Testing ATM Connections 198
- Verifying PNNI Communications 200
- Managing IMA Groups 203
- Configuring IMA Groups 205
- • 1 = IMA version 1.0 206
- • 2 = IMA version 1.1 206
- Configuring an IMA Link 207
- Deleting an IMA Group 208
- Testing an IMA Link 209
- Managing Loopbacks 210
- AXSM Command Reference 211
- APS Overview 212
- APS Architecture Modes 212
- AXSM/A and AXSM/B APS Issues 214
- Syntax Description 214
- Related Commands 215
- Attributes 215
- Before Adding a Connection 218
- Adding a Connection 218
- Traffic Parameters 219
- Service Types, CDV, and CTD 220
- Routing Parameters 221
- Frame Discard 221
- Restrictions 222
- Local-Only Parameters 223
- OAM and Failure Management 225
- Syntax (AXSM) 225
- • 1 = enable 229
- Error Messages 231
- Value 1.3 2 4 3 64 1 275 236
- Setting the Correct Port SCT 238
- Usage Guidelines 241
- Related Command 241
- Syntax Description (AXSM) 243
- -ds3 1.16 244
- AXSM-E, AXSM-XG Dependencies 247
- Using the Correct SCT 250
- Syntax (AXSM-XG) 251
- Example 261
- • AXSM-E : 1–32 270
- • AXSM-XG: 1–126 270
- Examples 278
- Attributes (AXSM) 291
- Attributes (AXSM-E, AXSM-XG) 291
- Display Command History 302
- Configuration successful 305
- Generic Syntax Description 306
- Thresholds for SONET Section 307
- Thresholds for SONET Line 307
- Thresholds for SONET Path 307
- Thresholds for DS3 308
- Thresholds for E3 308
- Thresholds for PLCP 308
- Table 5-15 BERT Test Patterns 318
- Background 322
- Types of Card Statistics 325
- Syntax (SONET) 347
- Syntax Description (SONET) 347
- Syntax (DS3) 347
- Syntax Description (DS3) 348
- Syntax (E1) 349
- Syntax Description (E1) 349
- Syntax (E3) 349
- Syntax Description (E3) 349
- <SEFS24Hr> 351
- Syntax (Sonet Lines) 352
- 15-minute intervals to 500 353
- Chapter 5 354
- <SEFS24>] 359
- Specifying the Core Mask 375
- Redundancy Policy 376
- Aborting a Core Dump 376
- Example (AXSM-E) 388
- Example (AXSM-32-T1E1-E) 388
- AXSM, AXSM-E, AXSM-XG) 400
- Attributes (AXSM-32-T1E1-E) 401
- Example (AXSM) 435
- Example (AXSM-XG) 436
- Syntax (AXSM-E, AXSM-XG) 442
- Example (SCT 2) 443
- Example SCT 3 445
- Step 1 Execute tstdelay 458
- Step 2 Check the results 458
- • ATLAS programmed data 465
- • SABRE programmed data 465
- The dspcons Output on AXSM 472
- Syntax Description 498
- Example 499
- Attributes 500
- alarm type 513
- Syntax (AXSM, AXSM-XG) 523
- Syntax (AXSM-E) 523
- (AXSM-E) 523
- Display Output 523
- Display Lines—AXSM 539
- Version Numbering Conventions 623
- Firmware Filenames 623
- Version Numbers 623
Related products and manuals for Networking Cisco RPM-XF
Networking Cisco IAD2431-16FXS User's Guide
(94 pages)
(94 pages)
Networking Cisco 2613 User Manual
(16 pages)
(16 pages)
Networking Cisco IOS Router User Manual
(9 pages)
(9 pages)
Networking Cisco NM-HDV-1E1-30E - 30 Enhanced Channel E1 Voice/Fax Network Module Service Manual
(24 pages)
(24 pages)
Networking Cisco 15216 EDFA2 Specifications
(252 pages)
(252 pages)
Networking Cisco EZXS88W User's Guide
(10 pages)
(10 pages)
Networking Cisco DPC 3925 User's Guide
(106 pages)
(106 pages)
Networking Cisco OL-6900-01 User Manual
(126 pages)
(126 pages)
Networking Cisco RT31P2-NA User Manual
(73 pages)
(73 pages)
Networking Cisco 675E User's Guide
(50 pages)
(50 pages)
(15 pages)
Networking Cisco PXM Version 1.1 User's Guide
(972 pages)
(972 pages)
Networking Cisco uBR904 Specifications
(38 pages)
(38 pages)
© 2020, manymanuals.com. All rights reserved. | 0.074 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals