Cisco SCE8000 Specifications Page 25
- Page / 778
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
1-3
Cisco SCE 8000 CLI Command Reference
Chapter 1 Command-Line Interface
Authorization and Command Mode Levels (Hierarchy)
CLI Command Mode Hierarchy
The set of all CLI commands is grouped in hierarchical order, according to the type of the commands.
The first two levels in the hierarchy are the User Exec and Privileged Exec modes. These are
non-configuration modes in which the set of available commands enables the monitoring of the Cisco
SCE platform, file system operations, and other operations that cannot alter the configuration of the
Cisco SCE platform.
The next levels in the hierarchy are the Global and Interface configuration modes, which hold a set of
commands that control the global configuration of the Cisco SCE platform and its interfaces. Any of the
parameters set by the commands in these modes should be saved in the startup configuration, such that
in the case of a reboot, the Cisco SCE platform restores the saved configuration.
Table 1-2 shows the available CLI modes.
Admin Password required. For use by general administrators, the
Admin authorization level enables configuration and
management of the Cisco SCE platform.
10
#
Root Password required. For use by technical field engineers,
the Root authorization level enables configuration of all
advanced settings, such as debug and disaster recovery.
The Root level is used by technical engineers only.
15
#>
Table 1-1 Authorization Levels (continued)
Level Description Value Prompt
Table 1-2 CLI Modes
Mode Description Level Prompt indication
User Exec Initial mode. Also allows monitoring of the system
(show commands).
User/Viewer
SCE8000>
Privileged Exec General administration; file system manipulations
and control of basic parameters that do not change
the configuration of the Cisco SCE platform.
• Admin
• Root
• SCE8000#
• SCE8000#>
Global Configuration Configuration of general system parameters, such
as DNS, host name, and time zone.
• Admin
• Root
• SCE8000(config)#
• SCE8000(config)#>
Management Interface
Configuration
Configuration of management interface parameters,
such as the Ethernet interface properties and
selection of the active port.
• Admin
• Root
• SCE8000(config if)#
• SCE8000(config if)#>
Interface
Configuration
Configuration of specific system interface
parameters, for the following interface modes.
• linecard interface
• specific traffic interface
• Admin
• Root
• SCE8000(config if)#
• SCE8000(config if)#>
- Cisco Systems, Inc 1
- CONTENTS 3
- Contents 10
- About This Guide 19
- Document Revision History 20
- Organization 20
- Related Publications 20
- Conventions 21
- Command-Line Interface 23
- CLI Authorization Levels 24
- CLI Command Mode Hierarchy 25
- • E1: interface Linecard 0 27
- • E3: (traffic ports) 27
- Prompt Indications 28
- Example: 29
- CLI Help Features 31
- Argument Help 32
- Command History 34
- Keyboard Shortcuts 34
- Auto-Completion 35
- FTP User Name and Password 36
- Managing Command Output 37
- Creating a CLI Script 39
- CLI Command Reference 41
- • 0 (user) 43
- • 5 (viewer) 43
- • 10 (admin) 43
- • 15 (root) 43
- • none—Use no authentication 48
- EXAMPLE 1 54
- EXAMPLE 2 54
- • Permit/deny field 56
- • attack-detector 62
- • access-list 62
- • Action—report 63
- command to disable it 95
- is 60 minutes 123
- General Guidelines 124
- Recurring Configurations 124
- Specifying Explicit Days 125
- Example 1 125
- Example 2 125
- Example 3 125
- • /system/preconf 143
- • /system/prevconf 144
- Disable multi-mapping: 163
- Load Balancing 176
- High Availability (Failover) 176
- Figure 2-1 Disable Command 181
- • full—Full duplex 183
- • half—Half duplex 183
- Figure 2-2 Enable Command 185
- • Must begin with a letter 186
- • Cannot contain spaces 186
- • Are case-sensitive 186
- • General configuration files 190
- • Static party DB files 190
- • start—Starts recording 195
- • stop—Stops recording 195
- Command Description 206
- EXEC authorization level 214
- • global-controller bandwidth 222
- • global-controller name 222
- EXAMPLE 1: 249
- EXAMPLE 2: 249
- Ipv6-IANA 271
- • warning 292
- • Adding an entry 297
- • Removing an entry 297
- • traffic-engineering skip 327
- • vpn skip 327
- • END_USER_E164 343
- • END_USER_IMSI 343
- • END_USER_NAI 343
- • END_USER_SIP-URI 343
- • END_USER_PRIVATE 343
- • Link Usage RDRs (LURs) 353
- • Package Usage RDRs (PURs) 353
- • Category 1—40 MB 364
- • Category 2—24 MB 364
- • Category 3—8 MB 364
- • Category 4—8 MB 364
- Priorities 369
- Table 2-8 Valid Mode Settings 373
- • The host ends with .com 384
- User Authorization Guidelines 390
- • Calling station ID 401
- • NAS port 401
- • Username 401
- • CDP mode 422
- Counter Definitions 514
- Current values: 514
- Peak values: 514
- Event counters: 515
- • Has no mapping 517
- Examples Example 1 521
- Example 4 522
- TP-IP-range 533
- EXAMPLE 3 542
- EXAMPLE 4 542
- • duplex 550
- • IP address 550
- • auto-fail-over 550
- • Quota rate control 574
- • Maximum size of the buffer 574
- SCE8000> 597
- • Main connection 602
- SCE8000(config)#> 678
- • SNMP traps 683
- • Enterprise traps 683
- Authorization: admin 686
- Examples 686
- IP specification 740
- Port specification 741
- Tunnel ID specification 741
- Traffic counter name 741
- • Action = flow-capture 743
- IP Specification 744
- Limitations 747
- • Link-0 757
- • Link-1 757
- • VAS server is enabled 759
- • Server has a VLAN tag 759
- • Server Group ID 764
- • SCE 8000: 0-63 764
- Direction 771
- PIR Values 772
© 2020, manymanuals.com. All rights reserved. | 0.187 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals