Cisco 15216 EDFA2 Specifications Page 87
- Page / 252
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
5-21
Cisco ONS 15216 EDFA2/EDFA2-A Operations Guide, R2.4
July 2004
Chapter 5 SNMP MIB Configuration
5.4.11 OpGroup
Table 5-18 cerent15216EdfaOpGroup Variable Descriptions
Variable Syntax
Maximum
Access Description
cerent15216Edfa
OpStatus
idle(1),
pending(2),
inProgress(3),
aborted(4)
Read-only The status of the current operation.
cerent15216Edfa
OpResult
Integer Read-only This value is used to save the error result (if any) of
the last operation. Success is indicated by a value of
0.
For DB backup and restore the following results are
possible:
0: Success.
1: Restore or backup operation cannot obtain the db
semaphore. This error should never occur because
the cerent15216EdfaOpGroup MIB implementation
does not allow more than one operation to be in
progress at a time.
2: This will occur if there is a problem with opening
cerent15216EdfaOpDbFileName. This could be
because the file system is full, the file does not exist
in the case of a restore, or the file already exists on
the file system in the case of a backup.
3: This occurs if the backup procedure cannot obtain
a configuration value.
4: This occurs during a restore if the CRC in file
specified by cerent15216EdfaOpDbFileName is not
correct. For example, a corrupted backup file.
5: This occurs during a restore if there is a parsing
error. This could occur if the backup file was created
by a version of software that is not compatible with
the current software version.
-1: Unknown internal failure.
cerent15216Edfa
OpRequestId
Integer Read-write The request identifier for this operation. This is
provided to allow managers to match results with
actions.
cerent15216Edfa
OpSaveConfig
idle(1),
perform(2),
abort(3)
Read-write To save the configuration of the management and
optical modules, write “perform” to this object.
- Operations Guide 1
- CONTENTS 3
- 3 Installation 3-1 4
- 5 SNMP MIB Configuration 5-1 5
- 6 ASH Commands 6-1 7
- 7 File Transfers 7-1 8
- 8 Provisioning with TL1 8-1 8
- 9 TL1 Commands 9-1 9
- 10 Troubleshooting 10-1 10
- Contents 11
- About this Guide 19
- Document Conventions 20
- Obtaining Documentation 21
- Documentation Feedback 22
- Submitting a Service Request 23
- Applications 25
- 1.3 Key Features 26
- 1.3.2 Gain Flattening 27
- 1.3.3 Transient Suppression 27
- 1.3.4 Low Noise 27
- 1.3.6 SNMP MIBs 28
- 1.3.7 TL1 28
- Technical Specifications 29
- 2.1.1 Maximum Input Power 30
- 2.1.2 Channel Loading 30
- 2.2 Electrical Specifications 32
- 2.3 Mechanical Specifications 32
- 2.4 External Features 33
- 2.5 Front Panel 34
- Installation 37
- Chapter 3 Installation 38
- 3.3 SC/UPC Optical Ports 39
- 3.4 Communications 41
- 3.4.2 Alarm LEDs 42
- 3.4.2.2 FAIL LED (Red) 43
- 3.4.2.3 LOS LED (Yellow) 43
- 3.4.2.4 Ethernet Socket LEDs 43
- 3.4.3.1 Required Equipment 43
- Click OK when done 45
- Remote Site 47
- 3.4.4.2 Modem Signals 48
- 3.4.4.3 Modem Power Up 48
- • 19,200 baud 49
- • No parity 49
- • 8 bits per character 49
- Table 3-6 Modem Settings 49
- GND RXD TXD 50
- 54
- 4.2 Set IP Address 55
- 4.4 Set Date and Time 56
- 4.7 Set Gain 57
- 4.8 Set Alarm Thresholds 57
- CISCO ONS 15216 58
- ALARM OUT 58
- °C. Setting 60
- 4.9 Set Password 62
- 4.10 Add Users 63
- 4.11 Save Changes 63
- 4.12 Log Off 64
- SNMP MIB Configuration 67
- 5.1.2.1 SNMP Agent 68
- 5.1.2.2 SNMP MIBs 69
- 5.1.2.3 SNMP Manager 70
- 5.2.1 Creating a View 72
- Table 5-5 Creating a View 73
- 5.2.2.1 Set CommunityEntry 74
- 5.3 Setting Up for CTM Access 76
- 5.4 Tables and Groups 78
- 5.4.2 AgentControlGroup 79
- 5.4.3 AlarmEntry 79
- 5.4.4 BootEntry 80
- 5.4.5 BootImageEntry 81
- 5.4.6 CfgGroup 81
- 5.4.7 FfsFileEntry 83
- 5.4.8 FfsOpGroup 84
- 5.4.9 LogEventControl 85
- 5.4.10 LogEventEntry 85
- 5.4.11 OpGroup 86
- 5.4.12 OverallControl 89
- 5.4.13 OverallStatusGroup 89
- 5.4.14 PumpCfgEntry 90
- 5.4.15 PumpStatusEntry 93
- 5.4.16 RtcDateAndTime 94
- 5.4.17 SromIpMgmtGroup 95
- 5.5 Setting Up Traps 96
- 5.5.2 Set Trap Command 97
- 5.6 Retrieving Information 98
- 5.6.2 Date and Time 99
- 5.6.3 Power Gain 100
- 5.6.4 Case Temperature 101
- 5.6.4.2.1 CtmpMin 102
- 5.6.4.2.2 CtmpMax 102
- 5.6.5 Power Bus 103
- 5.6.6 Input Power (Signal) 104
- 5.6.6.1.2 InPowerdBm 105
- 5.6.7 Output Power 106
- 5.6.7.2.2 LpoutDeviation 107
- July 2004 109
- 5.6.9 Alarm Entry 110
- Table 5-28 SNMP Alarms 111
- Table 5-29 SNMP Events 112
- ASH Commands 115
- Chapter 6 ASH Commands 116
- 6.2 Configuration Commands 121
- 6.3 Administrative Commands 124
- 6.3.3 help Command 125
- 6.3.4 history Command 125
- 6.4 Shell Commands 126
- • snmp.cfg 127
- • passwd 127
- 6.6 SNMP Commands 128
- IP_address 130
- 6.6.5 snmp mib get Command 131
- 6.6.6 snmp mib list Command 131
- 6.6.8 snmp row get Command 133
- 6.6.9 snmp row set Command 133
- {IP_address 134
- Syntax Description 135
- 6.6.14 snmp table get Command 137
- 6.7 User Commands 138
- 6.7.2 user entry edit Command 139
- (IP address) 143
- 6.9 Restore Commands 144
- 6.10 Manufacturer Mode 144
- File Transfers 147
- 7.1.3 FTP Commands 149
- 7.2 TFTP File Transfer 150
- Provisioning with TL1 151
- 8.2 Set IP Address 153
- 8.4 Set Date and Time 154
- 8.7 Set Gain 155
- 8.8 Set Alarm Thresholds 155
- RTRV-TH-DWDM::ALL:124; 156
- RTRV-TH-EQPT::ALL:125; 156
- °C. Valid 159
- °C. Valid entries 160
- °C. Setting this value to 0 160
- 8.9 Set Password 161
- 8.10 Add Users 162
- 8.11 Log Off 162
- CPY-MEM:::123:: 163
- ,FFS,CFG; 163
- INIT-SYS::ALL:124::1; 163
- TL1 Commands 165
- 9.3 Notation 166
- Chapter 9 TL1 Commands 167
- 9.6.1 ACT-USER 174
- 9.6.2 ALW-MSG-ALL 175
- 9.6.3 APPLY 178
- 9.6.4 CANC-USER 178
- 9.6.5 COPY-RFILE 179
- 9.6.6 CPY-MEM 180
- CPY-MEM:Amp01::123::LOG,MEM,; 181
- CPY-MEM:Amp01::123::,,; 181
- 9.6.7 DLT-RFILE 182
- 9.6.8 DLT-USER-SECU 182
- 9.6.9 ED-DAT 183
- 9.6.10 ED-DWDM 183
- Example 9-12 ED-DWDM Command 184
- 9.6.11 ED-EQPT 185
- 9.6.12 ED-NE-GEN 185
- =192.168.3.4,CLI=ASH; 186
- 9.6.13 ED-PID 187
- 9.6.14 ED-USER-SECU 187
- 9.6.15 ENT-USER-SECU 188
- 9.6.16 INH-MSG-ALL 189
- 9.6.17 INIT-SYS 192
- 9.6.18 REPT ALM DWDM 193
- 9.6.19 REPT ALM EQPT 195
- 9.6.21 REPT EVT FXFR 200
- 9.6.22 RTRV-ALM-ALL 201
- 9.6.23 RTRV-ALM-DWDM 204
- 9.6.24 RTRV-ALM-EQPT 205
- 9.6.25 RTRV-AO 207
- 9.6.26 RTRV-ATTR-ALL 208
- 9.6.27 RTRV-ATTR-DWDM 210
- 9.6.28 RTRV-ATTR-EQPT 212
- 9.6.29 RTRV-COND-ALL 213
- RTRV-COND-ALL:Amp01::229::; 214
- 9.6.30 RTRV-COND-DWDM 216
- 9.6.31 RTRV-COND-EQPT 217
- 9.6.32 RTRV-DFLT-SECU 219
- 9.6.33 RTRV-DWDM 220
- 9.6.34 RTRV-EQPT 222
- 9.6.35 RTRV-HDR 223
- 9.6.36 RTRV-INV 224
- 9.6.37 RTRV-NE-GEN 225
- 9.6.38 RTRV-RFILE 226
- 9.6.39 RTRV-TH-DWDM 227
- 9.6.40 RTRV-TH-EQPT 228
- RTRV-TH-EQPT:Amp01:ALL:123::; 229
- 9.6.41 RTRV-TOD 230
- 9.6.42 RTRV-USER-SECU 231
- 9.6.43 SET-ATTR-DWDM 232
- 9.6.44 SET-ATTR-EQPT 233
- 9.6.45 SET-ATTR-SECUDFLT 235
- 9.6.46 SET-TH-DWDM 235
- 9.6.47 SET-TH-EQPT 236
- 9.6.48 STA-LOCL-RST 238
- Troubleshooting 239
- 10.1 Alarm Indicators 240
- 10.1.1.3 LOS LED (Yellow) 241
- 10.1.1.4 Ethernet Socket LEDs 241
- ONS_15216_EDFA2_IP_Address 243
- RTRV-INV:Amp01:ALL:123; 247
- RTRV-NE-GEN:AMP01::ALL::; 249
- 10.2.9 Lost Password 250
Related products and manuals for Networking Cisco 15216 EDFA2
Networking Cisco EZXS88W User's Guide
(10 pages)
(10 pages)
Networking Cisco DPC 3925 User's Guide
(106 pages)
(106 pages)
Networking Cisco OL-6900-01 User Manual
(126 pages)
(126 pages)
Networking Cisco RT31P2-NA User Manual
(73 pages)
(73 pages)
Networking Cisco 675E User's Guide
(50 pages)
(50 pages)
Networking Cisco PXM Version 1.1 User's Guide
(972 pages)
(972 pages)
Networking Cisco uBR904 Specifications
(38 pages)
(38 pages)
Networking Cisco WS-C3020 User Manual
(8 pages)
(8 pages)
Networking Cisco AG310 User's Guide
(87 pages)
(87 pages)
Networking Cisco NSLU2 Datasheet
(14 pages)
(14 pages)
Networking Cisco WRT160NL User Manual
(68 pages)
(68 pages)
© 2020, manymanuals.com. All rights reserved. | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals