Cisco SCE8000 Specifications Page 360
- Page / 778
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
2-320
Cisco SCE 8000 CLI Command Reference
Chapter 2 CLI Command Reference
pqi upgrade file
pqi upgrade file
Upgrades the application using the specified pqi file and any specified upgrade options. This procedure
may take up to 5 minutes.
pqi upgrade file filename [options options]
Syntax Description
Command Default None
Command Modes Interface Linecard Configuration
Command History This table includes the following release-specific history entries:
Usage Guidelines A pqi upgrade file is suitable for upgrading only from specific previously installed pqi files. The upgrade
procedure checks that an upgrade is possible from the currently installed pqi file. The upgrade procedure
will be stopped with an error message if the upgrade is not possible.
When upgrading the application in a cascaded system, use the force failure-condition command to force
failure in the active SCE 8000 platform. (See System Upgrades in the Cisco SCE8000 10GBE Software
Configuration Guide or System Upgrades in the Cisco SCE8000 GBE Software Configuration Guide.)
Authorization: admin
Examples The following example shows how to upgrade using the anr100155.pqi file. No options are specified.
SCE8000>enable 10
Password:<cisco>
SCE8000#config
SCE8000(config)#interface linecard 0
SCE8000(config if)#pqi upgrade file anr100155.pqi
SCE8000(config if)#
Related Commands
filename Filename of the pqi application file to be used for the upgrade.
options Upgrade options. Use the show pqi file command to display the available
options.
Release Modification
2.5.7 This command was introduced.
Command Description
show pqi file Displays information about the specified application file.
force failure-condition Forces a virtual failure condition, and exits from the failure condition, when
performing an application upgrade.
- Cisco Systems, Inc 1
- CONTENTS 3
- Contents 10
- About This Guide 19
- Document Revision History 20
- Organization 20
- Related Publications 20
- Conventions 21
- Command-Line Interface 23
- CLI Authorization Levels 24
- CLI Command Mode Hierarchy 25
- • E1: interface Linecard 0 27
- • E3: (traffic ports) 27
- Prompt Indications 28
- Example: 29
- CLI Help Features 31
- Argument Help 32
- Command History 34
- Keyboard Shortcuts 34
- Auto-Completion 35
- FTP User Name and Password 36
- Managing Command Output 37
- Creating a CLI Script 39
- CLI Command Reference 41
- • 0 (user) 43
- • 5 (viewer) 43
- • 10 (admin) 43
- • 15 (root) 43
- • none—Use no authentication 48
- EXAMPLE 1 54
- EXAMPLE 2 54
- • Permit/deny field 56
- • attack-detector 62
- • access-list 62
- • Action—report 63
- command to disable it 95
- is 60 minutes 123
- General Guidelines 124
- Recurring Configurations 124
- Specifying Explicit Days 125
- Example 1 125
- Example 2 125
- Example 3 125
- • /system/preconf 143
- • /system/prevconf 144
- Disable multi-mapping: 163
- Load Balancing 176
- High Availability (Failover) 176
- Figure 2-1 Disable Command 181
- • full—Full duplex 183
- • half—Half duplex 183
- Figure 2-2 Enable Command 185
- • Must begin with a letter 186
- • Cannot contain spaces 186
- • Are case-sensitive 186
- • General configuration files 190
- • Static party DB files 190
- • start—Starts recording 195
- • stop—Stops recording 195
- Command Description 206
- EXEC authorization level 214
- • global-controller bandwidth 222
- • global-controller name 222
- EXAMPLE 1: 249
- EXAMPLE 2: 249
- Ipv6-IANA 271
- • warning 292
- • Adding an entry 297
- • Removing an entry 297
- • traffic-engineering skip 327
- • vpn skip 327
- • END_USER_E164 343
- • END_USER_IMSI 343
- • END_USER_NAI 343
- • END_USER_SIP-URI 343
- • END_USER_PRIVATE 343
- • Link Usage RDRs (LURs) 353
- • Package Usage RDRs (PURs) 353
- • Category 1—40 MB 364
- • Category 2—24 MB 364
- • Category 3—8 MB 364
- • Category 4—8 MB 364
- Priorities 369
- Table 2-8 Valid Mode Settings 373
- • The host ends with .com 384
- User Authorization Guidelines 390
- • Calling station ID 401
- • NAS port 401
- • Username 401
- • CDP mode 422
- Counter Definitions 514
- Current values: 514
- Peak values: 514
- Event counters: 515
- • Has no mapping 517
- Examples Example 1 521
- Example 4 522
- TP-IP-range 533
- EXAMPLE 3 542
- EXAMPLE 4 542
- • duplex 550
- • IP address 550
- • auto-fail-over 550
- • Quota rate control 574
- • Maximum size of the buffer 574
- SCE8000> 597
- • Main connection 602
- SCE8000(config)#> 678
- • SNMP traps 683
- • Enterprise traps 683
- Authorization: admin 686
- Examples 686
- IP specification 740
- Port specification 741
- Tunnel ID specification 741
- Traffic counter name 741
- • Action = flow-capture 743
- IP Specification 744
- Limitations 747
- • Link-0 757
- • Link-1 757
- • VAS server is enabled 759
- • Server has a VLAN tag 759
- • Server Group ID 764
- • SCE 8000: 0-63 764
- Direction 771
- PIR Values 772
© 2020, manymanuals.com. All rights reserved. | 0.161 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals