Cisco SCE8000 Specifications Page 694
- Page / 778
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
2-654
Cisco SCE 8000 CLI Command Reference
Chapter 2 CLI Command Reference
snmp-server user
If you are configuring less number of SNMPv3 user or few ad hoc configurations, you need not disable
the SNMP agent. You may notice a delay of few seconds for the configuration to take effect.
SNMPv3 users are not shown in the running-configuration. To see a list of configured users, use the show
snmp user command. The SNMPv3 user configurations are persistent across restarts of the Cisco SCE.
To remove any or all users, you must explicitly remove them using no snmp-server user command.
If you configure a group and configure few users for that group. You must copy the
running-configuration to startup-configuration to preserve the group configurations across restarts of the
Cisco SCE. If you do not copy the running-configuration to startup-configuration, the user configuration
is preserved and group configuration is deleted. To make the groups and users usable again, you need to
configure the groups again.
Authorization: admin
Examples
SCE8000> enable 10
Password: <cisco>
SCE8000# configure
SCE8000(config)#> no snmp-server
SCE8000(config)#> snmp-server user ipUser group ipGroup auth MD5-auth auth-pass-phrase
password
Note: Do not forget to enable the SNMP agent after all the user configuration, to make
them active.
SCE8000(config)#> snmp-server user ipUser01 group ipGroup auth SHA-auth auth-pass-phrase
passwordsha
Note: Do not forget to enable the SNMP agent after all the user configuration, to make
them active.
SCE8000(config)#> snmp-server user ifUserNoAuth group ifGroupReadOnly
Note: Do not forget to enable the SNMP agent after all the user configuration, to make
them active.
SCE8000(config)#> snmp-server user ifUserRW group ifGroup auth SHA-auth auth-pass-phras
passwordsha priv AES-priv priv-pass-phrase passwordaes
Note: Do not forget to enable the SNMP agent after all the user configuration, to make
them snmp-server user active.
SCE8000(config)#> snmp-server enable
SCE8000(config)#> end
SCE8000#>
- Cisco Systems, Inc 1
- CONTENTS 3
- Contents 10
- About This Guide 19
- Document Revision History 20
- Organization 20
- Related Publications 20
- Conventions 21
- Command-Line Interface 23
- CLI Authorization Levels 24
- CLI Command Mode Hierarchy 25
- • E1: interface Linecard 0 27
- • E3: (traffic ports) 27
- Prompt Indications 28
- Example: 29
- CLI Help Features 31
- Argument Help 32
- Command History 34
- Keyboard Shortcuts 34
- Auto-Completion 35
- FTP User Name and Password 36
- Managing Command Output 37
- Creating a CLI Script 39
- CLI Command Reference 41
- • 0 (user) 43
- • 5 (viewer) 43
- • 10 (admin) 43
- • 15 (root) 43
- • none—Use no authentication 48
- EXAMPLE 1 54
- EXAMPLE 2 54
- • Permit/deny field 56
- • attack-detector 62
- • access-list 62
- • Action—report 63
- command to disable it 95
- is 60 minutes 123
- General Guidelines 124
- Recurring Configurations 124
- Specifying Explicit Days 125
- Example 1 125
- Example 2 125
- Example 3 125
- • /system/preconf 143
- • /system/prevconf 144
- Disable multi-mapping: 163
- Load Balancing 176
- High Availability (Failover) 176
- Figure 2-1 Disable Command 181
- • full—Full duplex 183
- • half—Half duplex 183
- Figure 2-2 Enable Command 185
- • Must begin with a letter 186
- • Cannot contain spaces 186
- • Are case-sensitive 186
- • General configuration files 190
- • Static party DB files 190
- • start—Starts recording 195
- • stop—Stops recording 195
- Command Description 206
- EXEC authorization level 214
- • global-controller bandwidth 222
- • global-controller name 222
- EXAMPLE 1: 249
- EXAMPLE 2: 249
- Ipv6-IANA 271
- • warning 292
- • Adding an entry 297
- • Removing an entry 297
- • traffic-engineering skip 327
- • vpn skip 327
- • END_USER_E164 343
- • END_USER_IMSI 343
- • END_USER_NAI 343
- • END_USER_SIP-URI 343
- • END_USER_PRIVATE 343
- • Link Usage RDRs (LURs) 353
- • Package Usage RDRs (PURs) 353
- • Category 1—40 MB 364
- • Category 2—24 MB 364
- • Category 3—8 MB 364
- • Category 4—8 MB 364
- Priorities 369
- Table 2-8 Valid Mode Settings 373
- • The host ends with .com 384
- User Authorization Guidelines 390
- • Calling station ID 401
- • NAS port 401
- • Username 401
- • CDP mode 422
- Counter Definitions 514
- Current values: 514
- Peak values: 514
- Event counters: 515
- • Has no mapping 517
- Examples Example 1 521
- Example 4 522
- TP-IP-range 533
- EXAMPLE 3 542
- EXAMPLE 4 542
- • duplex 550
- • IP address 550
- • auto-fail-over 550
- • Quota rate control 574
- • Maximum size of the buffer 574
- SCE8000> 597
- • Main connection 602
- SCE8000(config)#> 678
- • SNMP traps 683
- • Enterprise traps 683
- Authorization: admin 686
- Examples 686
- IP specification 740
- Port specification 741
- Tunnel ID specification 741
- Traffic counter name 741
- • Action = flow-capture 743
- IP Specification 744
- Limitations 747
- • Link-0 757
- • Link-1 757
- • VAS server is enabled 759
- • Server has a VLAN tag 759
- • Server Group ID 764
- • SCE 8000: 0-63 764
- Direction 771
- PIR Values 772
© 2020, manymanuals.com. All rights reserved. | 0.265 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals