Cisco MWR 2941 Installation Manual Page 289
- Page / 710
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
-289
Cisco MWR 2941 Mobile Wireless Edge Router Release 3.5 Command Reference, Cisco IOS Release 15.1(3)MR
OL-26895-01
Chapter Cisco MWR 2941 Router Command Reference, Release 15.1(3)MR
network-clock-select input-stratum4
network-clock-select input-stratum4
The network-clock-select input-stratum4 command allows you to downgrade a clock source from
Stratum3 to Stratum 4. To configure a clock source as Stratum 3, use the no form of this command.
network-clock-select input-stratum4
no network-clock-select input-stratum4
Defaults The default setting is for onboard E1/T1 ports is Stratum 3; the default setting for E1/T1 HWIC ports is
Stratum 4.
Note You cannot configure E1/T1 HWIC ports as Stratum3.
Command Modes Global configuration
Command History
Examples The following example shows how to use the network-clock-select command:
Router# config t
Router(config)# network-clock-select input-stratum4
Router(config)# exit
Related Commands
Release Modification
12.4(19)MR2 This command was introduced.
12.2(33)MRA This command was integrated into Cisco IOS Release 12.2(33)MRA.
15.0(1)MR This command was integrated into Cisco IOS Release 15.0(1)MR.
Command Description
set network-clocks
force-reselect
Forces the router to re-select the network clock.
- Release 15.1(3)MR 1
- Configuring a Policy Map 14
- Restrictions 15
- Policy Map Configuration Mode 27
- Class Characteristics 27
- Predefined Default Class 27
- Tail Drop or WRED 27
- Fragments 28
- If ID Choice Is Anything Else 72
- Unique Device Identifier 73
- Cisco HWIC-4SHDSL 88
- SNAP Encapsulation Example 96
- OL-26895-01 105
- • n393—1 to 10. Default is 4 133
- • proxy-register 187
- • list access-list 187
- • route-map map-name 187
- Support for Serial Lines 194
- Syntax Description 195
- Keepalive Time Interval 203
- Line Failure 203
- Dropped Packets 203
- DSCP Values 226
- Match Packets on DSCP Values 227
- • match access-group 231
- • match input-interface 231
- • match mpls experimental 231
- • match protocol 231
- Precedence Values and Names 233
- IPv4-Specific Traffic Match 233
- IPv6-Specific Traffic Match 234
- Support Restrictions 237
- ATM Mode Example 247
- CAS Mode Example 247
- Router(config)# no mpls ip 250
- Release 12.2(33)SRB 259
- • QL-PRC 275
- • QL-SSU-A 275
- • QL-SSU-B 275
- • QL-SEC 275
- • QL-DNU 275
- All Supported Platforms 303
- Hierarchical Policy Maps 304
- How Bandwidth Is Calculated 305
- • conform-action is transmit 311
- • exceed-action is drop 311
- • violate-action is drop 311
- Token Buckets 314
- Updating Token Buckets 315
- Marking Traffic 315
- Two-Rate Policing 316
- Syntax for Percent 318
- Command Application 332
- • Data encapsulation type 334
- • Control protocol 334
- • 4—1 packet every 16 seconds 336
- • 3—1 packet every 8 seconds 336
- • 2—1 packet every 4 seconds 336
- • 1—1 packet every 2 seconds 336
- • 0—1 packet every second 336
- Command Description 341
- Router(config)# exit 358
- Weighted Fair Queueing 366
- • Control network loops 376
- • Handle link failures 376
- • Improve convergence time 376
- the following adapters: the 409
- to specify the “from-field” 412
- • EF (expedited forwarding) 420
- Precedence Value and Queueing 421
- 2. ip tos reflect 429
- 3. ip tos tos-value 429
- Command Compatibility 440
- Bit Settings 440
- Precedence Value 441
- Committed Information Rate 449
- IMA Group 456
- M-PAIR Group 456
- 1-PAIR and 2-PAIR Group 456
- DSL Group with 1 Pair 458
- DSL Group with 2 Pairs 458
- DSL Group with 3 Pairs 458
- DSL Group with 4 Pairs 458
- • Interface name and number 471
- • Identifier (group ID) 475
- ADSL: Example 490
- • Domain name 495
- • Domain index 495
- • Domain level 495
- Field Description 504
- Reliability Errors 524
- Protocol Errors 524
- UNI Id Identifier of the UNI 526
- EVC Id Identifier of the EVC 526
- • Local and remote OAM mode 528
- • Remote platform identity 528
- • Remote loopback events 531
- Traffic Policing: Example 583
- Tunnel Marking: Example 588
- ATM Shared Port Adapter 590
- (continued) 595
- Policing 597
- Policing and Shaping 599
- Traffic Shaping: Example 600
- UDP encapsulation 613
- • priority is 128 647
- Router(config-if)# 648
- • Up to 2 queues 670
- • Up to 2 interfaces 670
- • 1 queue and 1 interface 670
- Router(config-if)# switchport 672
- GRE Tunneling Example 693
- Peak Value 705
- Average Value 705
- Burst Value 705
- Activating the Primary Member 709
- Activating the Backup Member: 709
Related products and manuals for Networking Cisco MWR 2941
Networking Cisco WMP110 User Manual
(2 pages)
(2 pages)
Networking Cisco Ex SERIES User Manual
(15 pages)
(15 pages)
Networking Cisco Soho series User Manual
(4 pages)
(4 pages)
Networking Cisco AS2509-RJ User Manual
(26 pages)
(26 pages)
Networking Cisco WKPC54G User Manual
(2 pages)
(2 pages)
Networking Cisco Dial NMS User Manual
(8 pages)
(8 pages)
Networking Cisco DMA2100 User Manual
(3 pages)
(3 pages)
Související produkty a manuály pro ne GBC 6360
ne GBC 27 Uživatelský manuál
(4 stránky)
(4 stránky)
ne GBC 250T Uživatelský manuál
(3 stránky)
(3 stránky)
ne GBC 4120 Uživatelský manuál
(6 stránky)
(6 stránky)
ne GBC TL300 Uživatelský manuál
(4 stránky)
(4 stránky)
ne GBC 120 Uživatelský manuál
(4 stránky)
(4 stránky)
ne GBC H 950 Uživatelský manuál
(16 stránky)
(16 stránky)
© 2020, manymanuals.com. All rights reserved. | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals