Cisco MWR 2941 Installation Manual Page 636
- Page / 710
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
-636
Cisco MWR 2941 Mobile Wireless Edge Router Release 3.5 Command Reference, Cisco IOS Release 15.1(3)MR
OL-26895-01
Chapter Cisco MWR 2941 Router Command Reference, Release 15.1(3)MR
snmp-server enable traps ethernet cfm crosscheck
• After enabling cross-check (ethernet cfm mep crosscheck enable), the device waits for the
cross-check-start timeout value specified (ethernet cfm mep crosscheck enable-timeout). When
the timeout period has elapsed, the device will cross-check the list of remote MEPs it has learned
via CCMs against the static list that has been configured (mep crosscheck mpid vlan). For each
remote MEP that is configured in the static list and for which the device has not received a CCM, a
mep-missing trap is generated.The mep-missing trap has the following fields:
• Service ID designating the customer service instance to which the event belongs, as configured on
the device reporting the event.
• MAC address of the device reporting the event. This is typically the Bridge Brain MAC address.
• MPID of the remote MEP that is being reported missing.
• MAC address of the remote MEP that is being reported missing.
The mep-unknown trap (cEtherCfmXCheckUnknown) notifies the NMS that the device received CCMs
from a remote MEP that it was not expecting to be part of the service instance.
The mep-unknown trap is generated in the following case:
• After cross-check is in an operational state, the device dynamically examines the list of statically
configured remote MEPs against what it learns from CCMs. This occurs after cross-check is enabled
and the timer has expired. When the device receives a CCM with non-zero hold time from a remote
MEP that does not exist in the static list, the device raises a mep-unknown trap.
The mep-unknown trap has the following fields:
• Service ID designating the customer service instance to which the event belongs, as configured on
the device reporting the event.
• MAC address of the device reporting the event. This is typically the Bridge Brain MAC address.
• MPID of the remote MEP that is being reported unknown.
• MAC address of the remote MEP that is being reported unknown.
The service-up trap (cEtherCfmXCheckServiceUp) notifies the NMS that the device received CCMs
from all remote MEPs within a given service instance.
The service-up trap is generated in the following case:
• When the device receives CCMs from all remote statically configured MEPs before the expiration
of the crosscheck enable-timeout period.
The service-up trap has the following fields:
• Service ID designating the customer service instance to which the event belongs, as configured on
the device reporting the event.
• MAC address of the device reporting the event. This is typically the Bridge Brain MAC address.
Examples The following example shows how to enable SNMP trap generation for Ethernet CFM continuity check
events when an unexpected (unconfigured) MEP comes up:
Router (config)# snmp-server enable traps ethernet cfm crosscheck mep-unknown
- Release 15.1(3)MR 1
- Configuring a Policy Map 14
- Restrictions 15
- Policy Map Configuration Mode 27
- Class Characteristics 27
- Predefined Default Class 27
- Tail Drop or WRED 27
- Fragments 28
- If ID Choice Is Anything Else 72
- Unique Device Identifier 73
- Cisco HWIC-4SHDSL 88
- SNAP Encapsulation Example 96
- OL-26895-01 105
- • n393—1 to 10. Default is 4 133
- • proxy-register 187
- • list access-list 187
- • route-map map-name 187
- Support for Serial Lines 194
- Syntax Description 195
- Keepalive Time Interval 203
- Line Failure 203
- Dropped Packets 203
- DSCP Values 226
- Match Packets on DSCP Values 227
- • match access-group 231
- • match input-interface 231
- • match mpls experimental 231
- • match protocol 231
- Precedence Values and Names 233
- IPv4-Specific Traffic Match 233
- IPv6-Specific Traffic Match 234
- Support Restrictions 237
- ATM Mode Example 247
- CAS Mode Example 247
- Router(config)# no mpls ip 250
- Release 12.2(33)SRB 259
- • QL-PRC 275
- • QL-SSU-A 275
- • QL-SSU-B 275
- • QL-SEC 275
- • QL-DNU 275
- All Supported Platforms 303
- Hierarchical Policy Maps 304
- How Bandwidth Is Calculated 305
- • conform-action is transmit 311
- • exceed-action is drop 311
- • violate-action is drop 311
- Token Buckets 314
- Updating Token Buckets 315
- Marking Traffic 315
- Two-Rate Policing 316
- Syntax for Percent 318
- Command Application 332
- • Data encapsulation type 334
- • Control protocol 334
- • 4—1 packet every 16 seconds 336
- • 3—1 packet every 8 seconds 336
- • 2—1 packet every 4 seconds 336
- • 1—1 packet every 2 seconds 336
- • 0—1 packet every second 336
- Command Description 341
- Router(config)# exit 358
- Weighted Fair Queueing 366
- • Control network loops 376
- • Handle link failures 376
- • Improve convergence time 376
- the following adapters: the 409
- to specify the “from-field” 412
- • EF (expedited forwarding) 420
- Precedence Value and Queueing 421
- 2. ip tos reflect 429
- 3. ip tos tos-value 429
- Command Compatibility 440
- Bit Settings 440
- Precedence Value 441
- Committed Information Rate 449
- IMA Group 456
- M-PAIR Group 456
- 1-PAIR and 2-PAIR Group 456
- DSL Group with 1 Pair 458
- DSL Group with 2 Pairs 458
- DSL Group with 3 Pairs 458
- DSL Group with 4 Pairs 458
- • Interface name and number 471
- • Identifier (group ID) 475
- ADSL: Example 490
- • Domain name 495
- • Domain index 495
- • Domain level 495
- Field Description 504
- Reliability Errors 524
- Protocol Errors 524
- UNI Id Identifier of the UNI 526
- EVC Id Identifier of the EVC 526
- • Local and remote OAM mode 528
- • Remote platform identity 528
- • Remote loopback events 531
- Traffic Policing: Example 583
- Tunnel Marking: Example 588
- ATM Shared Port Adapter 590
- (continued) 595
- Policing 597
- Policing and Shaping 599
- Traffic Shaping: Example 600
- UDP encapsulation 613
- • priority is 128 647
- Router(config-if)# 648
- • Up to 2 queues 670
- • Up to 2 interfaces 670
- • 1 queue and 1 interface 670
- Router(config-if)# switchport 672
- GRE Tunneling Example 693
- Peak Value 705
- Average Value 705
- Burst Value 705
- Activating the Primary Member 709
- Activating the Backup Member: 709
Related products and manuals for Networking Cisco MWR 2941
Networking Cisco WMP110 User Manual
(2 pages)
(2 pages)
Networking Cisco Ex SERIES User Manual
(15 pages)
(15 pages)
Networking Cisco Soho series User Manual
(4 pages)
(4 pages)
Networking Cisco AS2509-RJ User Manual
(26 pages)
(26 pages)
Networking Cisco WKPC54G User Manual
(2 pages)
(2 pages)
Networking Cisco Dial NMS User Manual
(8 pages)
(8 pages)
Networking Cisco DMA2100 User Manual
(3 pages)
(3 pages)
(2 pages)Relacionado con productos y manuales para Accesorios para eléctrica Dwyer ISDP
(4 paginas)© 2020, manymanuals.com. All rights reserved. | 0.070 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals