Cisco MWR 2941 Installation Manual Page 604
- Page / 710
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
-604
Cisco MWR 2941 Mobile Wireless Edge Router Release 3.5 Command Reference, Cisco IOS Release 15.1(3)MR
OL-26895-01
Chapter Cisco MWR 2941 Router Command Reference, Release 15.1(3)MR
show policy-map interface
Related Commands
Match Match criteria specified for the class of traffic. Choices include criteria such as
the Layer 3 packet length, IP precedence, IP differentiated services code point
(DSCP) value, Multiprotocol Label Switching (MPLS) experimental value,
access groups, and quality of service (QoS) groups. For more information
about the variety of match criteria that are available, see the “Classifying
Network Traffic” module in the Cisco IOS Quality of Service Solutions
Configuration Guide.
police Indicates that traffic policing has been enabled. Display includes the CIR, PIR
(in both a percentage of bandwidth and in bps) and the bc and be in bytes and
milliseconds. Also displays the optional conform, exceed, and violate actions,
if any, and the statistics associated with these optional actions.
Table 1-55 show policy-map interface Field Descriptions (continued)
Field Description
Command Description
bandwidth remaining
ratio
Specifies a bandwidth-remaining ratio for class queues and
subinterface-level queues to determine the amount of unused (excess)
bandwidth to allocate to the queue during congestion.
class-map Creates a class map to be used for matching packets to a specified class.
compression header ip Configures RTP or TCP IP header compression for a specific class.
drop Configures a traffic class to discard packets belonging to a specific class.
match packet length
(class-map)
Specifies the length of the Layer 3 packet in the IP header as a match
criterion in a class map.
police Configures traffic policing.
police (percent) Configures traffic policing on the basis of a percentage of bandwidth
available on an interface.
police (two rates) Configures traffic policing using two rates, the CIR and the PIR.
policy-map Creates or modifies a policy map that can be attached to one or more
interfaces to specify a service policy.
priority Specifies that low-latency behavior must be given to a traffic class and
configures multiple priority queues.
shape (percent) Specifies average or peak rate traffic shaping on the basis of a percentage
of bandwidth available on an interface.
show class-map Display all class maps and their matching criteria.
show interfaces Displays statistics for all interfaces configured on a router or access server.
show mls qos Displays MLS QoS information.
show policy-map Displays the configuration of all classes for a specified service policy map
or all classes for all existing policy maps.
show policy-map class Displays the configuration for the specified class of the specified policy
map.
- Release 15.1(3)MR 1
- Configuring a Policy Map 14
- Restrictions 15
- Policy Map Configuration Mode 27
- Class Characteristics 27
- Predefined Default Class 27
- Tail Drop or WRED 27
- Fragments 28
- If ID Choice Is Anything Else 72
- Unique Device Identifier 73
- Cisco HWIC-4SHDSL 88
- SNAP Encapsulation Example 96
- OL-26895-01 105
- • n393—1 to 10. Default is 4 133
- • proxy-register 187
- • list access-list 187
- • route-map map-name 187
- Support for Serial Lines 194
- Syntax Description 195
- Keepalive Time Interval 203
- Line Failure 203
- Dropped Packets 203
- DSCP Values 226
- Match Packets on DSCP Values 227
- • match access-group 231
- • match input-interface 231
- • match mpls experimental 231
- • match protocol 231
- Precedence Values and Names 233
- IPv4-Specific Traffic Match 233
- IPv6-Specific Traffic Match 234
- Support Restrictions 237
- ATM Mode Example 247
- CAS Mode Example 247
- Router(config)# no mpls ip 250
- Release 12.2(33)SRB 259
- • QL-PRC 275
- • QL-SSU-A 275
- • QL-SSU-B 275
- • QL-SEC 275
- • QL-DNU 275
- All Supported Platforms 303
- Hierarchical Policy Maps 304
- How Bandwidth Is Calculated 305
- • conform-action is transmit 311
- • exceed-action is drop 311
- • violate-action is drop 311
- Token Buckets 314
- Updating Token Buckets 315
- Marking Traffic 315
- Two-Rate Policing 316
- Syntax for Percent 318
- Command Application 332
- • Data encapsulation type 334
- • Control protocol 334
- • 4—1 packet every 16 seconds 336
- • 3—1 packet every 8 seconds 336
- • 2—1 packet every 4 seconds 336
- • 1—1 packet every 2 seconds 336
- • 0—1 packet every second 336
- Command Description 341
- Router(config)# exit 358
- Weighted Fair Queueing 366
- • Control network loops 376
- • Handle link failures 376
- • Improve convergence time 376
- the following adapters: the 409
- to specify the “from-field” 412
- • EF (expedited forwarding) 420
- Precedence Value and Queueing 421
- 2. ip tos reflect 429
- 3. ip tos tos-value 429
- Command Compatibility 440
- Bit Settings 440
- Precedence Value 441
- Committed Information Rate 449
- IMA Group 456
- M-PAIR Group 456
- 1-PAIR and 2-PAIR Group 456
- DSL Group with 1 Pair 458
- DSL Group with 2 Pairs 458
- DSL Group with 3 Pairs 458
- DSL Group with 4 Pairs 458
- • Interface name and number 471
- • Identifier (group ID) 475
- ADSL: Example 490
- • Domain name 495
- • Domain index 495
- • Domain level 495
- Field Description 504
- Reliability Errors 524
- Protocol Errors 524
- UNI Id Identifier of the UNI 526
- EVC Id Identifier of the EVC 526
- • Local and remote OAM mode 528
- • Remote platform identity 528
- • Remote loopback events 531
- Traffic Policing: Example 583
- Tunnel Marking: Example 588
- ATM Shared Port Adapter 590
- (continued) 595
- Policing 597
- Policing and Shaping 599
- Traffic Shaping: Example 600
- UDP encapsulation 613
- • priority is 128 647
- Router(config-if)# 648
- • Up to 2 queues 670
- • Up to 2 interfaces 670
- • 1 queue and 1 interface 670
- Router(config-if)# switchport 672
- GRE Tunneling Example 693
- Peak Value 705
- Average Value 705
- Burst Value 705
- Activating the Primary Member 709
- Activating the Backup Member: 709
Related products and manuals for Networking Cisco MWR 2941
Networking Cisco WMP110 User Manual
(2 pages)
(2 pages)
Networking Cisco Ex SERIES User Manual
(15 pages)
(15 pages)
Networking Cisco Soho series User Manual
(4 pages)
(4 pages)
Networking Cisco AS2509-RJ User Manual
(26 pages)
(26 pages)
Networking Cisco WKPC54G User Manual
(2 pages)
(2 pages)
Networking Cisco Dial NMS User Manual
(8 pages)
(8 pages)
Networking Cisco DMA2100 User Manual
(3 pages)
(3 pages)
(2 pages)© 2020, manymanuals.com. All rights reserved. | 0.058 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals