Cisco SCE 1000 2xGBE User's Guide Page 107
- Page / 490
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 4 Installation and Startup
System Configuration
SCE 1000 2xGBE Release 2.0.10 User Guide
OL-7117-02 4-45
The system will ask for FTP path:
Enter a full FTP path of the remote destination:
Step 6 The system informs you that the configuration is complete.
Committing configuration...
Configuration completed successfully.
Saving configuration...
Writing general configuration file to temporary location...
Backing-up general configuration file...
Copy temporary file to final location...
Done!
EXAMPLE #1:
Following is an example of a configuration that the user aborted due to errors detected in the
configuration.
Note that no confirmation is requested for the decision to abort the setup. Had there been no
errors, confirmation would have been requested before aborting.
Data collection for the system configuration is completed.
Would you like to view the new configuration before it is applied? [yes/no]:
n
Found errors in the new configuration, would you like to view them? [yes]: y
The following errors were found:
Warning - RDR formatter destination 10.1.1.1 is not allowed in the IP
access-class.
Warning - default Gateway 10.1.1.1 is not allowed in the IP access-class.
Warning - IP Access list (1) conflicts with Telnet Access list (2) as
follows:
Access list 2 permits all addresses while Access list 1 denies it.
Apply and Save this configuration? [yes/no]: n
Setup procedure aborted, no configuration changes made.
- SCE 1000 2xGBE Release 2.0.10 1
- User Guide 1
- OL-7117-02 i 3
- Contents 10
- Preface 13
- Document Content 14
- Document Conventions 15
- Related Publications 15
- Cisco TAC Website 16
- Opening a TAC Case 16
- Regulatory Compliance 19
- EC Declaration of Conformity 20
- CSA NRTL (Canada) 21
- Regulatory Symbols 21
- Warning Definition Statement 22
- Ground Connection Warning 24
- Grounded Equipment Warning 24
- Grounding Warning 24
- Protective Earth Warning 24
- Ground Conductor Warning 24
- SELV Circuit Warning 26
- Battery Handling Warning 26
- Fan Tray Removal Warning 27
- Overview 29
- Chapter 1 Overview 30
- Service Control Capabilities 31
- The SCE Platform 32
- Management and Collection 33
- Subscriber Management 34
- Collection 34
- Topology 37
- SCE Platform Configuration 38
- Failure Detection Mechanism 38
- Bypass Mechanism 38
- Functionality 39
- Physical Installation 39
- Chapter 2 Topology 40
- Physical Installation 40
- Redundancy 41
- Failure and Recovery 42
- Topology-Related Parameters 43
- Connection Mode Parameter 44
- On-Failure Mode Parameter 44
- Command Line Interface 47
- CLI Authorization Levels 48
- OL-7117-02 3-3 49
- CLI Command Hierarchy 50
- OL-7117-02 3-5 51
- 3-6 OL-7117-02 52
- OL-7117-02 3-7 53
- 3-8 OL-7117-02 54
- Exiting Modes 55
- Prompt Indications 56
- CLI Help Features 57
- The [no] Prefix 58
- Command History 59
- Keyboard Shortcuts 59
- Tab Completion 60
- FTP User Name and Password 60
- CLI Scripts 61
- Installation and Startup 63
- Step 3: Preparing to Install 64
- SCE 1000 Dimensions 65
- Site Requirement Guidelines 65
- Airflow 66
- Site Requirements 67
- Installation 68
- Installation Precautions 69
- Installation 70
- OL-7117-02 4-13 75
- Back Panel 76
- OL-7117-02 4-15 77
- 4-16 OL-7117-02 78
- OL-7117-02 4-17 79
- Step 2 Refasten the screws 80
- Front Panel 81
- Front Panel 82
- Table 4-6 SCE 1000 Ports 82
- Powering up 85
- Connecting the Local Console 86
- OL-7117-02 4-25 87
- System Configuration 88
- System Configuration 90
- OL-7117-02 4-29 91
- OL-7117-02 4-31 93
- 4-32 OL-7117-02 94
- OL-7117-02 4-33 95
- 4-34 OL-7117-02 96
- Entry Formats 97
- Order of Entries 98
- OL-7117-02 4-37 99
- Step 8: Configuring SNMP 100
- OL-7117-02 4-39 101
- 4-40 OL-7117-02 102
- OL-7117-02 4-41 103
- 4-42 OL-7117-02 104
- OL-7117-02 4-43 105
- 4-44 OL-7117-02 106
- OL-7117-02 4-45 107
- 4-46 OL-7117-02 108
- OL-7117-02 4-47 109
- 4-48 OL-7117-02 110
- OL-7117-02 4-49 111
- Configuring Auto-Negotiation 112
- OL-7117-02 4-51 113
- 4-52 OL-7117-02 114
- Examining the LEDs 115
- 4-54 OL-7117-02 116
- Final Tests 117
- Viewing the User Log 118
- Configuration and Management 119
- 5-2 OL-7117-02 120
- File-system Operations 121
- Changing Directories 122
- Displaying Working Directory 122
- Working with Files 123
- Copying a File 124
- Displaying File Contents 125
- Unzipping a File 125
- 5-8 OL-7117-02 126
- OL-7117-02 5-9 127
- 5-10 OL-7117-02 128
- OL-7117-02 5-11 129
- 5-12 OL-7117-02 130
- OL-7117-02 5-13 131
- Step 3 Type 132
- OL-7117-02 5-15 133
- Passwords 134
- Changing Passwords 135
- Encryption 136
- OL-7117-02 5-19 137
- The User Log 138
- Copying the User Log 140
- Rebooting the SCE Platform 143
- 5-26 OL-7117-02 144
- EXAMPLE: 145
- Control Configuration 147
- 6-2 OL-7117-02 148
- OL-7117-02 6-3 149
- Removing an Access List 150
- Telnet Interface 151
- SNMP Interface 152
- IP Configuration 153
- Default Gateway 154
- Show IP Route 154
- IP Advertising 155
- Configuring IP Advertising 156
- Show IP Advertising 156
- Time Clocks and Time Zone 157
- Setting the Clock 158
- Setting the Calendar 158
- Setting the Time Zone 159
- Enabling SNTP unicast client 160
- OL-7117-02 6-15 161
- Domain Name (DNS) Settings 162
- Name Servers 163
- Domain Name 164
- Host Table 164
- The RDR Formatter 165
- RDR Formatter Destinations 166
- Categories 167
- Priority 167
- Protocol Version 168
- Forwarding Modes 168
- 6-24 OL-7117-02 170
- OL-7117-02 6-25 171
- The RDR Formatter 172
- OL-7117-02 6-27 173
- 6-28 OL-7117-02 174
- OL-7117-02 6-29 175
- 6-30 OL-7117-02 176
- SNMP Protocol 177
- Configuration via SNMP 178
- Security Considerations 178
- SNMP Community Strings 179
- 6-34 OL-7117-02 180
- Configuring Traps 181
- 6-36 OL-7117-02 182
- OL-7117-02 6-37 183
- 6-38 OL-7117-02 184
- OL-7117-02 6-39 185
- Cisco Enterprise MIB 186
- Failure Recovery Mode 187
- Step 1 Type exit 188
- XAMPLE: 189
- 6-44 OL-7117-02 190
- Configuring Applications 191
- 6-46 OL-7117-02 192
- OL-7117-02 6-47 193
- 6-48 OL-7117-02 194
- Line Configuration 195
- 7-2 OL-7117-02 196
- Selecting the Tunneling Mode 197
- 7-4 OL-7117-02 198
- OL-7117-02 7-5 199
- Traffic Rules 200
- Traffic counters 200
- Configuring Traffic Counters 201
- Configuring Traffic Rules 201
- 7-8 OL-7117-02 202
- OL-7117-02 7-9 203
- 7-10 OL-7117-02 204
- OL-7117-02 7-11 205
- Configuring TOS Marking 206
- Editing the Connection Mode 207
- Enforcing the Link Mode 208
- [no] link failure-reflection 209
- Auto-negotiation 210
- Managing Subscribers 213
- Subscriber Overview 214
- Subscriber Overview 215
- Aging Subscribers 216
- Subscriber Files 217
- 8-6 OL-7117-02 218
- OL-7117-02 8-7 219
- 8-8 OL-7117-02 220
- OL-7117-02 8-9 221
- Monitoring Subscribers 222
- Displaying Subscribers 224
- Monitoring Subscribers 226
- Subscriber Aging 230
- Service Attacks 233
- Attack Detection 234
- Attack Detection Thresholds 235
- Attack Handling 235
- Subscriber Notification 236
- Configuring Attack Detectors 237
- 9-6 OL-7117-02 238
- Default Attack Detector 239
- Specific Attack Detectors 240
- 9-10 OL-7117-02 242
- OL-7117-02 9-11 243
- Managing Attack Filtering 244
- Preventing Attack Filtering 245
- Forcing Attack Filtering 245
- Monitoring Attack Filtering 246
- 9-16 OL-7117-02 248
- Troubleshooting 249
- Front Panel LEDs 250
- OL-7117-02 10-3 251
- Front Panel LEDs 252
- Management Link 253
- RDR Reports 254
- Table 10-3 RDR Reports 255
- RDR Reports 256
- Subscriber side and 257
- Network side ports on the 257
- SCE Platform are 257
- Check the GBE 257
- GBE Interfaces Connectivity 258
- 10-12 OL-7117-02 260
- OL-7117-02 10-13 261
- User Log 262
- Maintenance 265
- Replacing the Fan Module 266
- Replacing the Power Module 267
- Step 1 Turn the module OFF 268
- Step 9 Turn the module ON 269
- CLI Command Reference 271
- Functional Information 272
- Syntax and Conventions 273
- All Modes 274
- OL-7117-02 A-5 275
- Exec Mode Commands 276
- OL-7117-02 A-7 277
- A-8 OL-7117-02 278
- OL-7117-02 A-9 279
- A-10 OL-7117-02 280
- OL-7117-02 A-11 281
- A-12 OL-7117-02 282
- OL-7117-02 A-13 283
- A-14 OL-7117-02 284
- OL-7117-02 A-15 285
- [no] ip domain-lookup 286
- OL-7117-02 A-17 287
- [no] ip rmi-adapter 288
- OL-7117-02 A-19 289
- [no] ip rpc-adapter 290
- OL-7117-02 A-21 291
- A-22 OL-7117-02 292
- OL-7117-02 A-23 293
- RDR-formatter history-size 294
- OL-7117-02 A-25 295
- A-26 OL-7117-02 296
- {number [1-4]}] 297
- [no] service RDR-formatter 298
- [no] service telnetd 299
- A-30 OL-7117-02 300
- OL-7117-02 A-31 301
- A-32 OL-7117-02 302
- [no] sntp broadcast client 303
- A-34 OL-7117-02 304
- [no] attack-detector default 305
- A-36 OL-7117-02 306
- [no] attack-filter 307
- L2TP identify-by 308
- OL-7117-02 A-39 309
- A-40 OL-7117-02 310
- OL-7117-02 A-41 311
- [no] silent 312
- OL-7117-02 A-43 313
- A-44 OL-7117-02 314
- OL-7117-02 A-45 315
- A-46 OL-7117-02 316
- OL-7117-02 A-47 317
- A-48 OL-7117-02 318
- [no] traffic-counter 319
- [no] traffic-rule 319
- Appendix A 320
- SAGE GUIDELINES 320
- XAMPLE 1 320
- [no] ip tunnel mode 321
- [no] duplex mode 323
- [no] speed speed 324
- [no 325
- A-56 OL-7117-02 326
- [no] access-class number in 327
- A-58 OL-7117-02 328
- OL-7117-02 A-59 329
- A-60 OL-7117-02 330
- [no] blink slot slot-number 331
- A-62 OL-7117-02 332
- OL-7117-02 A-63 333
- A-64 OL-7117-02 334
- OL-7117-02 A-65 335
- A-66 OL-7117-02 336
- OL-7117-02 A-67 337
- A-68 OL-7117-02 338
- OL-7117-02 A-69 339
- [overwrite] 340
- OL-7117-02 A-71 341
- [no] history 342
- [no] history size size 342
- OL-7117-02 A-73 343
- A-74 OL-7117-02 344
- OL-7117-02 A-75 345
- A-76 OL-7117-02 346
- [more 347
- A-78 OL-7117-02 348
- OL-7117-02 A-79 349
- A-80 OL-7117-02 350
- OL-7117-02 A-81 351
- A-82 OL-7117-02 352
- OL-7117-02 A-83 353
- A-86 OL-7117-02 356
- OL-7117-02 A-87 357
- A-88 OL-7117-02 358
- OL-7117-02 A-89 359
- A-90 OL-7117-02 360
- OL-7117-02 A-91 361
- A-92 OL-7117-02 362
- OL-7117-02 A-93 363
- A-94 OL-7117-02 364
- OL-7117-02 A-95 365
- A-96 OL-7117-02 366
- OL-7117-02 A-97 367
- A-98 OL-7117-02 368
- OL-7117-02 A-99 369
- A-100 OL-7117-02 370
- OL-7117-02 A-101 371
- A-102 OL-7117-02 372
- OL-7117-02 A-103 373
- A-104 OL-7117-02 374
- OL-7117-02 A-105 375
- A-106 OL-7117-02 376
- OL-7117-02 A-107 377
- A-108 OL-7117-02 378
- OL-7117-02 A-109 379
- A-110 OL-7117-02 380
- OL-7117-02 A-111 381
- A-112 OL-7117-02 382
- OL-7117-02 A-113 383
- A-114 OL-7117-02 384
- OL-7117-02 A-115 385
- A-116 OL-7117-02 386
- OL-7117-02 A-117 387
- A-118 OL-7117-02 388
- OL-7117-02 A-119 389
- A-120 OL-7117-02 390
- OL-7117-02 A-121 391
- A-122 OL-7117-02 392
- OL-7117-02 A-123 393
- A-124 OL-7117-02 394
- Proprietary MIB Reference 395
- Using this Reference 396
- Config-Copy MIB Objects 397
- SCE Events 398
- OL-7117-02 B-5 399
- SCE-MIB Structure 400
- Appendix B 401
- SCE Events: pcubeSeEvents 406
- SCE Events: pcubeSeEvents 408
- OL-7117-02 B-17 411
- OL-7117-02 B-19 413
- B-20 OL-7117-02 414
- B-22 OL-7117-02 416
- OL-7117-02 B-23 417
- B-24 OL-7117-02 418
- OL-7117-02 B-25 419
- B-26 OL-7117-02 420
- OL-7117-02 B-27 421
- B-28 OL-7117-02 422
- OL-7117-02 B-29 423
- B-30 OL-7117-02 424
- OL-7117-02 B-31 425
- B-32 OL-7117-02 426
- OL-7117-02 B-33 427
- B-34 OL-7117-02 428
- OL-7117-02 B-35 429
- B-36 OL-7117-02 430
- OL-7117-02 B-37 431
- B-38 OL-7117-02 432
- OL-7117-02 B-39 433
- OL-7117-02 B-41 435
- B-42 OL-7117-02 436
- OL-7117-02 B-43 437
- B-44 OL-7117-02 438
- OL-7117-02 B-45 439
- B-46 OL-7117-02 440
- OL-7117-02 B-47 441
- B-48 OL-7117-02 442
- B-50 OL-7117-02 444
- OL-7117-02 B-51 445
- B-52 OL-7117-02 446
- OL-7117-02 B-53 447
- B-54 OL-7117-02 448
- OL-7117-02 B-55 449
- B-56 OL-7117-02 450
- Access RO 451
- TimeTicks 451
- B-58 OL-7117-02 452
- OL-7117-02 B-59 453
- B-60 OL-7117-02 454
- B-62 OL-7117-02 456
- OL-7117-02 B-63 457
- B-64 OL-7117-02 458
- OL-7117-02 B-65 459
- B-66 OL-7117-02 460
- B-68 OL-7117-02 462
- OL-7117-02 B-69 463
- B-70 OL-7117-02 464
- OL-7117-02 B-71 465
- B-72 OL-7117-02 466
- OL-7117-02 B-73 467
- Supported Standards 469
- Glossary of Terms 471
- Flow Bundle 472
- Inline connection mode 472
- Link mode 472
- Glossary of Terms 474
- OL-7117-02 1 475
- Index 476
- OL-7117-02 3 477
- OL-7117-02 5 479
- OL-7117-02 7 481
- OL-7117-02 9 483
- OL-7117-02 11 485
- OL-7117-02 13 487
- OL-7117-02 15 489
Related products and manuals for Networking Cisco SCE 1000 2xGBE
Networking Cisco 10005 Installation Guide
(46 pages)
(46 pages)
Networking Cisco 6260 Installation Guide
(244 pages)
(244 pages)
Networking Cisco 815 Specifications
(28 pages)
(28 pages)
Networking Cisco WES610N User Manual
(21 pages)
(21 pages)
Networking Cisco 510 User Manual
(2 pages)
(2 pages)
Networking Cisco WPC54GS User's Guide
(83 pages)
(83 pages)
Networking Cisco 10700 User's Guide
(602 pages)
(602 pages)
Networking Cisco ME 3800X Specifications
(622 pages)
(622 pages)
Networking Cisco uBR7100 Series User Manual
(12 pages)
(12 pages)
Networking Cisco 867W User Manual
(59 pages)
(59 pages)
Networking Cisco 7400 series User's Guide
(12 pages)
(12 pages)
© 2020, manymanuals.com. All rights reserved. | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals